Connection Options The Xpress Receiver and Cradle provide an audio output signal in three ways: a. FM Modulator -When using the XMC10A cradle with the FM modulator option, the XM audio signal can be received through your vehicle’s radio on selectable FM frequencies using the menu option included in your Xpress Receiver. (Refer to the User Guide.) The XM audio signal can then be played through your vehicle’s radio when that radio is tuned to one of the available frequencies. NOTE: To minimize rad

Failure to do so could result in personal injury or damage to your XMCommander or to your vehicle. Welcome Thank you for purchasing an XMCommander Satellite Radio FM Modulator and Receiver System. Your XMCommander gives you access to over 80 XM Satellite Radio channels of music, news, and information.* Your XMCommander must be used with the enclosed connecting devices to ensure maximum performance and safety. Professional installation is highly recommended. *XM subscription required for receptio

d. If the outside air temperature is cold, it may be beneficial to warm the adhesive backing on -8 the bracket using a portable hair dryer, or by holding the backing surface in front of a vehicle heater vent. e. Remove the plastic liner from the adhesive backing on the bracket, and fix the base in position on the surface; make sure the mounting pad is accurately positioned on the first try, since repositioning may be difficult, if not impossible. f. If the bracket is to be screwed in place, do n

2 Use the number buttons (0-9) to enter the channel number 0 and wait a moment until the channel is tuned or press the Select button. 3 The Radio ID is displayed until you tune to another channel Find Available FM Channels in Your Area Before attempting any of the procedures below, you should park your vehicle in a safe location Do not attempt to set up your FM channels or any onyX function while driving PowerConnect allows you to listen to XM audio through your vehicle’s FM radio You will first

2 Insert the Cassette Adapter into the vehicle’s cassette deck. You may need to turn on your vehicle’s stereo system in order to do so. 3 Insert the dock into the mount. 4 Insert your XpressRCi into the dock. 5 By default, your XpressRCi turns on automatically when it is plugged in and receiving power. If it does not, power on your XpressRCi by pressing the Power button. NOTE! You may experience a brief delay while your XpressRCi powers up. If you press the Power button during this time, you wil

User Guide Table of Contents Introduction 5 Features 6 Safety and Care Information 7 What’s in the Box? 9 XpressRCi Functions 10 Remote Control Functions 11 Control Knob and Select Button Basics 12 PowerConnect Vehicle Dock 13 Vehicle Installation 15 Step 1: Choose a Location for Your Radio 16 Step 2: Install the Dash or Vent Mount 18 Step 3: Mount the Magnetic Mount Antenna 22 Step 4: Route the Magnetic Mount Antenna Cable 27 Step 5: Connect the Magnetic Mount Antenna and PowerConnect Power Ada

If you have a cable run of more than 100 feet or need to run through diplexers and/or splitters use a signal preamplifier that is installed as close to the antenna as possible. 6. To avoid signal loss, do not attach the coaxial cable to the mast, use standoffs (fig. 7) (sold separately). Analog TV Pointing Method This method uses a conventional analog TV to chose the best spot for a DTV antenna. 1. Place antenna in as high location with as few obstructions in front of behind or to the sides of t

6. Connect 2 mast sections as shown in figure 6 (included in SDV9201K only) ENAiming the Antenna 7. Connect a good quality RG-6 coaxial cable to the transformer. Slide the weatherproof boot over the connection firmly until it seals (fig.7) (Cable sold separately) fig. 7 fig. 8 8. Attach cable standoff to mast as shown in figure 8 (included in SDV9201K only) Aiming the Antenna Before permanently mounting the antenna for digital television (DTV) reception it is a good idea to perform a quick sight

Same Side Adjustments – The P-series PowerPlate™ makes system adjustment easy by organizing all signal processing controls on one side of the amplifier. This layout allows convenient system adjustment and facilitates a variety of installation possibilities when access to the controls is desired. warnings and tips Always disconnect the battery ground wire before doing any work on your vehicle. Reconnect the cable only after the installation is complete and the wiring has been checked to make sure

THE FM TRANSMITTER OPTION MUST BE SET TO ”FM ON” IN THE SHUTTLE USER MENU. (REFER TO THE OWNER’S MANUAL, PUBLICATION NO.128-7193.) 2. IF THE SIR-CK3 IS INSTALLED USING THE WIRELESS FM SWITCHING BOX, SAT-SWB, OPTION, DO NOT CONNECT THE AUDIO CABLE TO THE LINE OUT CONNECTOR OF THE CRADLE. SHUTTLE ANTENNA TO VEHICLE +12 VDC POWER RECEPTACLE VEHICLE RADIO ANTENNA VEHICLE FM RADIO WIRELESS FM SWITCHING BOX SAT-SWB (PURCHASED SEPARATELY) TO VEHICLE RADIO ANTENNA JACK OPTIONAL AUDIO CABLE (PURCHASED SE