Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
d. If the outside air temperature is cold, it may be beneficial to warm the adhesive backing on -8 the bracket using a portable hair dryer, or by holding the backing surface in front of a vehicle heater vent. e. Remove the plastic liner from the adhesive backing on the bracket, and fix the base in position on the surface; make sure the mounting pad is accurately positioned on the first try, since repositioning may be difficult, if not impossible. f. If the bracket is to be screwed in place, do not remove the plastic liner from the adhesive backing. Use appropriate sheet metal or machine screws for this purpose. g. To mount the XMC10 cradle atop the swivel bracket, line up the slot at the rear of the cradle with the bracket retainer tab, and slide the cradle down so that the slot and tab mesh together in a locked position. NOTE: Allow a 72-hour period for the adhesive backing to cure completely. 128-7472 8 of 16 128-7472 9 of 16 -93. Using Other Manufacturer’s Mounts The XMC10 Cradle can also be installed using other manufacturer’s mounts; the mounting plate provisions on the rear and bottom of the cradle provideyou with two mounting options within the vehicle using various vehicle-specific aftermarket brackets. 4. Installing the Xpress XM® Receiver into the Cradle Install the Receiver as follows: a. After making sure the connectors and guide pin hole are properly lined up, gently lower the Xpress XM® Receiver into the cradle and press down on the Xpress XM® Receiver to mate the connectors together. The raised detent on the cradle will enter the notch on the rear of the Receiver, indicating the Xpress XM® is properly seated. b. The Xpress XM® Receiver should now be secured in the cradle SCREW HOLES (2) FOR DIRECT HARD MOUNTING PLASTIC LINER AND ADHESIVE BACKING SWIVEL ADJUSTMENT SCREW SWIVEL BRACKET SIDE (HORIZONTAL) MOUNTING CONFIGURATION VERTICAL MOUNTING CONFIGURATION XMC10 CRADLE ASSEMBLY SCREW HOLES (2) FOR DIRECT HARD MOUNTING PLASTIC LINER AND ADHESIVE BACKING SWIVEL ADJUSTMENT SCREW SWIVEL BRACKET SIDE (HORIZONTAL) MOUNTING CONFIGURATION VERTICAL MOUNTING CONFIGURATION XMC10 CRADLE ASSEMBLY Xpress XM® RECEIVERXpress XM® Xpress XM® RECEIVERXpress XM® RECEIVER REAR VIEW CRADLE FRONT VIEW GUIDE PIN CONNECTOR XMC10 RECEIVER NOTCH 5. Connection Options The Xpress Receiver and Cradle provide an audio output signal in three ways: a. FM Wireless Transmitter -When using the XMC10 cradle with the wireless FM transmitter option, the XM audio signal can be received SYSTEM CONNECTOR through your vehicle radio on selectable FM frequencies using the menu options included in your Xpress Receiver. (Refer to the Receiver owner’s manual.) The XM audio signal can then be played through your vehicle radio when the car radio is tuned to one of the available RAISED frequencies. DETENT SYSTEM CONNECTOR -10128- 7472 10 of 16 OPTIONAL SAT-RCA AUDIO CABLE (PURCHASED Y) (CONNECT TO AUXILIARY AUDIO OPTIONAL FM DIRECT ADAPTER XMFM-1 (PURCHASED SEPARATELY) TO VEHICLE RADIO ANTENNA JACK XMC10 CRADLE (RIGHT SIDE VIEW) OPTIONAL SAT-RCA AUDIO CABLE (PURCHASED Y) (CONNECT TO AUXILIARY AUDIO OPTIONAL FM DIRECT ADAPTER XMFM-1 (PURCHASED SEPARATELY) TO VEHICLE RADIO ANTENNA JACK XMC10 CRADLE (RIGHT SIDE VIEW) b. FM Direct Wiring -If the FM wireless transmitter does not provide satisfactory performance in your vehicle, use the optional FM Direct Adapter, Part # XMFM-1, which provides a hard-wired FM output. c. Low-Level Audio Output -For vehicles equipped with radio head units with auxiliary audio inputs, the audio signal can be routed through an optional audio cable (Part No. SATRCA) and applied to the auxiliary inputs of a radio or entertainment system. In this case, it is best to turn the Xpress Receiver FM modulator option off to avoid interference. -11 INPUTS ON VEHICLE HEAD UNIT.) 128-7472 11 of 16 128-7472 12 of 16 -12- 7. Mounting the Vehicle Antenna The antenna should be placed on a relatively flat surface on the vehicle exterior, preferably on the roof (high point) or on the trunk (convertible). To mount the antenna: a. Plug the antenna into the ANT connector on the back of the cradle. b. Place the antenna at the preferred location on the roof or trunk surface. If the vehicle is equipped with a roof or trunk rack, the antenna may have to be mounted off-center on the surface. The magnet will secure the antenna in the desired position. c. Apply power to the Xpress XM system as outlined in the associated User Guide and obtain an audio output. If no audio is heard, first check the signal strength indicator located on the bottom left corner of the display to ensure the antenna is receiving an optimum signal. If necessary, move the antenna to different SAT ANTENNA (TYPICAL) 12V-TO-5V DC POWER ADAPTER Xpress SYSTEM (TYPICAL) JU MP s. seek p. tu ne ..C ateg ory 12:00P A -1 A rtist Song 001 C han nel N am e positions on the surface until an audio output is heard. The desired antenna position should be marked with masking tape or by anothe...