Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
E
E
N
N
Installation
G
(Continued)
G
L
L
I
I
S
S
carefully to avoid damaging the speakers and the stereo
H
If your car is not wired for an audio unit:
❐ Final Installation
H
❐ Identify All Leads
Go to the fuse block and find the fuse port for the battery,
unit.
15
The first step in installation is to identify all the car wires
The speakers used must be able to handle more than 50
Lead Connections
16
usually marked BAT.
you’ll use when hooking up your sound system.
W (CQ-C1200U/C1120U)/45 W (CQ-C1110U/C1100U) of
Connect all wires, making sure that each connection is
As you identify each wire, we suggest that you label it
Speakers
audio power. If using an optional audio amplifier, the
insulated and secure. Bundle all loose wires and fasten
using masking tape and a permanent marker. This will
Identify the car speaker leads. There are two leads for
speakers should be able to handle the maximum amplifier
them with tape so they will not fall down later. Now insert
help avoid confusion when making connections later.
each speaker which are usually color coded.
output power. Speakers with low input ratings can be
the stereo unit into the mounting collar.
A handy way to identify the speaker leads and the speaker
damaged. Speaker impedance should measure 4–8 Ω,
Congratulations! After making a few final checks, you’re
Note: Do not connect the power connector to the stereo
they are connected with is to test the leads using a 1.5 V
which is typically marked on most speakers. Lower or
ready to enjoy your new auto stereo system.
unit until you have made all connections. If there are no
AA battery as follows.
higher impedance speakers will affect output and can
plastic caps on the stereo hooking wires, insulate all
❐ Final Checks
Hold one lead against one pole of the battery and stroke
cause both speaker and stereo unit damage.
exposed leads with electrical tape until you are ready to
the other lead across the other pole. You will hear a scrap-
1. Make sure that all wires are properly connected and
use them. Identify the leads in the following order.
ing sound in one of the speakers if you are holding a
Motor Antenna
insulated.
Connect the car motor antenna lead to the dark blue
Power Lead
speaker lead.
2. Make sure that the stereo unit is securely held in the
motor antenna relay control lead.
If your car has a radio or is pre-wired for one:
If not, keep testing different lead combinations until you
mounting collar.
(Do not confuse the antenna lead with blue/white stripe
Cut the connector wires one at a time from the plug (leav-
have located all the speaker leads. When you label them,
3. Turn on the ignition to check the unit for proper opera-
lead for a power amplifier.)
ing the leads as long as possible) so that you can work
include the speaker location for each.
tion.
with individual leads.
Antenna Motor
Battery
If you have difficulties, consult your nearest authorized
If your car is equipped with an automatic power antenna,
Connect the yellow battery lead to the correct radio wire
professional installer for assistance.
identify the car motor antenna lead by connecting one
or to the battery fuse port on the fuse block.
bulb tester lead to the car battery lead and touching the
Antenna
remaining exposed wires from the cut radio connector
Connect the antenna by plugging the antenna lead into the
plug one at a time. You will hear the antenna motor acti-
antenna receptacle.
vate when you touch the correct wire.
Equipment
Turn the ignition on to the accessory position, and ground
Antenna
Connect any optional equipment such as an amplifier,
one lead of the test bulb to the chassis.
The antenna lead is a thick, black wire with a metal plug at
according to the instructions furnished with the equip-
Touch the other lead of the test bulb to each of the
the end.
ment. Leave about 12" (30 cm) of distance between the
exposed wires from the cut radio connector plug. Touch
❐ Connect All Leads
speaker leads/amplifier unit and the antenna/antenna
one wire at a time until you find the outlet that causes the
extension cord. Read the operating and installation
test bulb to light.
Now that you have identified all the wires in the car, you
instructions of any equipment you will connect to this
are ready to begin connecting them to the stereo unit
unit.
Now turn the ignition off and then on. If the bulb also
wires. The wiring diagram (\ page 30) shows the proper
turns off and on, that outlet is the car power lead.
connections and color coding of the leads.
Power
Connect the red power lead to the correct car radio wire
If your car is not wired for an audio unit:
We strongly recommend that you test the unit before
or to the appropriate fuse port on the fuse block.
Go to the fuse block and find the fuse port for radio
making a final installation.
If the stereo unit functions properly with all these connec-
(RADIO), accessory (ACC), or ignition (IGN).
You can set the unit on the floor and make temporary con-
nections to test the unit. Use electrical tape to cover all
tions made, disconnect the wires and proceed to the final
Battery Lead
exposed wires.
installation.
If your stereo unit has a yellow lead, you will need to
locate the car’s battery lead. Otherwise you may ignore
Caution: Connect the red power lead last, after
this procedure. (The yellow battery lead provides continu-
you have made and insulated all other connec-
ous power to maintain a clock, memory storage, or other
tions.
function.)
If your car has a radio or is pre-wired for one:
Ground
With the ignition and headlights off, identify the car bat-
Connect the black ground lead of the power connector to
tery lead by grounding one lead of the test bulb to the
the metal car chassis.
chassis and checking the remaining exposed wires from
Speakers
the cut radio connector plug.
Connect the speaker wires. See the wiring diagram
(\ page 30) for the proper hookups. Follow the diagram
26
27
CQ-C1200U/C1120U/C1110U/C1100U
CQ-C1200U/C1120U/C1110U/C1100U
...Эта инструкция также подходит к моделям:
Автомагнитолы - CQC1110U (616.57 kb)
Автомагнитолы - CQC1120U (616.57 kb)
Автомагнитолы - CQC1200U (616.57 kb)