Оценок - 2, средний балл: 4.5 ( )

Производитель: Pioneer Размер: 331.75 kb Название файла: Язык инструкции:

(Когда повторно присоединяете ластичный ободок, направьте сторону с желобком вниз и присоедините его.) * Вытащить ластичный ободок легче, если передняя панель опущена. 2. Подберите подходящее место, где отверстия на скобе и стороне устройства будут совпадать. Если вы не планируете отсоединять переднюю панель, то она может быть закреплена с помощью поставляемого винта. Винт 3. Затяните два винта на каждой стороне. * Используйте винты со сферической головкой (5 мм х 8 мм) или винты с потайной головкой (5 мм х 9 мм), в зависимости от формы отверстий в скобе. Винт радиоприемника Connecting the Units Note: Depending on the kind of vehicle, the function of 3* and 5* may be different. In this case, be sure to connect 2* to 5* and 4* to 3*. 2. This Product 1. Rear output 3. Antenna jack 4. Fuse (10 A) 7. Connect leads of the same color to each other. 8. Cap (1*) Do not remove cap if this v terminal is not in use. 9. Yellow (3*) Back-up (or accessory) 11. Red (5*) Accessory (or back-up) 10. Yellow (2*) Connect to the constant 12 V supply terminal. 12. Red (4*) Connect to terminal controlled by ignition switch (12 V DC). ¿¿J 13. Black (chassis ground) Connect to a clean, paint-free metal location. 14. ISO connector Note: In some vehicles, the ISO connector may be divided into two. In this case, be sure to connect to both connectors. 27. Yellow/black If you use an equipment with Mute function, wire this lead to the Audio Mute lead on that equipment. If not, keep the Audio Mute lead free of any connections. 16. Connect with RCA cables (sold separately) 17. Power amp (sold separately) 5. Wired remote input Hard-wired remote control adaptor can be connected (sold separately). 18. Blue/white Connect to system control terminal of the power amp (max. 300 mA 12 V DC). 20. Blue/white (7*) Connect to Auto-antenna relay control terminal (max. 300 mA 12 V DC). 21. Blue/white (6*) 19. System remote control 22. The pin position of the ISO connector will differ depends on the type of vehicle. Connect 6* and 7* when Pin 5 is an antenna control type. In another type of vehicle, never connect 6* and 7*. 23. Left 24. Right 25. Rear Speaker © 1 © © © <] 25- Rear Speaker 26. Perform these connections when using the optional amplifier. 15. Speaker leads White: Front left 0 White/black: Front left © Gray: Front right 0 Gray/black: Front right 0 Green: Rear left 0 Green/black: Rear left © Violet: Rear right 0 Violet/black: Rear right © Connecting the Units Note: • When this unit is installed in a vehicle without ACC (accessory) position on the ignition switch, red cable must be wired to the terminal that can detect the operation of the ignition key. Otherwise, battery drain may result. ACC position No ACC position • Use this unit in other than the following conditions could result in fire or malfunction. — Vehicles with a 12-volt battery and negative grounding. — Speakers with 50 W (output value) and 4 ohm to 8 ohm (i...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: