Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Автомагнитолы - DEH-P80MP (1.31 mb)
Автомагнитолы - DEH-P80MP (1.34 mb)
Фрагмент инструкции
Fuse (1A) Fuse (20 A) Power supply wiring kit “RD-221” (sold separately) Multi-CD player (sold separately) Black (ground) To vehicle (metal) body. Red IP-BUS input (Blue) Orange/white To lighting switch terminal. ISO connector Note: In some vehicles, the ISO connector may be divided into two. In this case, be sure to connect to both connectors. Yellow/black If you use a cellular telephone, connect it via the Audio Mute lead on the cellular telephone. If not, keep the Audio Mute lead free of any connections. Speaker leads White : Front left + White/black : Front left . Gray : Front right + Gray/black : Front right . Green : Rear left + or Subwoofer + Green/black : Rear left . or Subwoofer . Violet : Rear right + or Subwoofer + Violet/black : Rear right . or Subwoofer . Red Not used. Yellow Not used. Blue/white (7*) To Auto-antenna relay control terminal (max. 300 mA 12 V DC). Blue/white (6*) Blue/white To system control terminal of the power amp (max. 300 mA 12 V DC). IP-BUS cable This product Antenna jack Refer to page7-8. 15 cm Fuse resistor Fuse holder Fuse holder The pin position of the ISO connector will differ depends on the type of vehicle. Connect 6* and 7* when Pin 5 is an antenna control type. In another type of vehicle, never connect 6* and 7*. Jack for Wired Remote Control Please see the Instruction Manual for the Wired Remote Control (sold separately). 15 cm ENGLISH Fig. 4 Connecting the Units Connecting to separately sold power amp IP-BUS input (Blue) ISO connector Note: In some vehicles, the ISO connector may be divided into two. In this case, be sure to connect to both connectors. Speaker leads White : Front left + White/black : Front left . Gray : Front right + Gray/black : Front right . Green : Rear left + or Subwoofer + Green/black : Rear left . or Subwoofer . Violet : Rear right + or Subwoofer + Violet/black : Rear right . or Subwoofer . IP-BUS cable Multi-CD player (sold separately) This product Antenna jack Subwoofer output or Non Fading Output (SUBWOOFER or NON-FADING OUTPUT) Front output (FRONT OUTPUT) Rear output (REAR OUTPUT) Refer to page3-6. Refer to page3-6. 15 cm Jack for Wired Remote Control 15 cm ENGLISH . + . + + . + . . + . + Perform these connections when using the optional amplifier. Blue/white (7*) To Auto-antenna relay control terminal (max. 300 mA 12 V DC). Blue/white (6*) Connecting cords with RCA pin plugs (sold separately) System remote control Power amp (sold separately) Rear speaker Subwoofer Subwoofer Rear speaker Front speaker Front speaker Power amp (sold separately) Power amp (sold separately) Left Right The pin position of the ISO connector will differ depends on the type of vehicle. Connect 6* and 7* when Pin 5 is an antenna control type. In another type of vehicle, never connect 6* and 7*. Note: Change the initial setting of this unit (refer to the Operation Manual). The subwoofer output of this unit is monaural. . + . + + . + . . + . + Perform these connections when using the optional amplifier. Blue/white (7*) To Auto-antenna relay control terminal (max. 300 mA 12 V DC). Blue/white (6*) Connecting cords with RCA pin plugs (sold separately) System remote control Power amp (sold separately) Rear speaker Subwoofer Subwoofer Rear speaker Front speaker Front speaker Power amp (sold separately) Power amp (sold separately) Left Right The pin position of the ISO connector will differ depends on the type of vehicle. Connect 6* and 7* when Pin 5 is an antenna control type. In another type of vehicle, never connect 6* and 7*. Note: Change the initial setting of this unit (refer to the Operation Manual). The subwoofer output of this unit is monaural. Fig. 5 Installation Installation Note: • Before finally installing the unit, connect the • If installation angle exceeds 60° from horizontal, wiring temporarily, making sure it is all connect-the unit might not give its optimum performance. ed up properly, and the unit and the system work (Fig. 6) properly. • Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. 60° • Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. • Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop. • The semiconductor laser will be damaged if it Fig. 6 overheats, so don’t install the unit anywhere hot — for instance, near a heater outlet. DIN Front/Rear-mount This unit can be properly installed either from “Front” (conventional DIN Front-mount) or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit chassis). For details, refer to the following illustrated installation methods. DIN Front-mount Installation with the rubber bush (Fig. 7) Holder After inserting the holder into the dashboard, then select the appropriate tabs 182 53 Dashboard according to the thickness of the dash- board mate...