Войти:
Оценок - 0, средний балл: 0 ( )

Инструкция по эксплуатации Pioneer, модель DEH-P80MP

Производитель: Pioneer
Размер: 959.72 kb
Название файла:
Язык инструкции:itenesfrdenl
Перейти к скачиванию



К этому устройству также есть другие инструкции:

Фрагмент инструкции


• When feeding electricity directly from the battery for the accessory (long red lead) through a battery cable, connect the accessory (short red lead) to the accessory circuit for the vehicle being supplied with electricity while the vehicle engine switch is set to the ACC position. • If the battery fuse for the vehicle is less than 10A, use a battery cable such as the RD-221 (sold sepa- rately) for the battery (yellow lead) and feed the electricity directly from the battery. • This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recre- ational vehicle, truck, or bus, check the battery volt- age. • Speakers connected to this unit must be high-power types with minimum rating of 60 W and impedance of 4 to 8 ohms. Connecting speakers with output and/or impedance values other than those noted here may result in the speakers catching fire, emit- ting smoke or becoming damaged. Connecting the Units Power cable connection (1) • When using this unit at 40W . 4ch. • When using this unit at 60W . 4ch and the accessory fuse for the vehicle is 10A or more. Black (ground) To vehicle (metal) body. Orange/white To lighting switch terminal. Multi-CD player (sold separately) Note: Depending on the kind of vehicle, the function of 3* and 5* may be different. In this case, be sure to connect 2* to 5* and 4* to 3*. Red (4*) To electric terminal controlled by ignition switch (12 V DC) ON/OFF. Red (5*) Accessory (or back-up) Yellow (2*) To terminal always supplied with power regardless of ignition switch position. Yellow (3*) Back-up (or accessory) Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF. Cap (1*) When not using this terminal, do not remove the cap. 1* 2* 4* 3* 5* Connect leads of the same color to each other. IP-BUS input (Blue) ISO connector Note: In some vehicles, the ISO connector may be divided into two. In this case, be sure to connect to both connectors. Yellow/black If you use a cellular telephone, connect it via the Audio Mute lead on the cellular telephone. If not, keep the Audio Mute lead free of any connections. Speaker leads White : Front left + White/black : Front left . Gray : Front right + Gray/black : Front right . Green : Rear left + or Subwoofer + Green/black : Rear left . or Subwoofer . Violet : Rear right + or Subwoofer + Violet/black : Rear right . or Subwoofer . Blue/white (7*) To Auto-antenna relay control terminal (max. 300 mA 12 V DC). Blue/white (6*) Blue/white To system control terminal of the power amp (max. 300 mA 12 V DC). IP-BUS cable Antenna jack Refer to page7-8. This product 15 cm Fuse resistor Fuse holder Fuse holder The pin position of the ISO connector will differ depends on the type of vehicle. Connect 6* and 7* when Pin 5 is an antenna control type. In another type of vehicle, never connect 6* and 7*. Jack for Wired Remote Control Please see the Instruction Manual for the Wired Remote Control (sold separately). 15 cm ENGLISH Fig. 3 Connecting the Units Power cable connection (2) • When using this unit at 60W . 4ch and the accessory fuse for the vehicle is less than 10A. Red To separately sold power supply wiring kit (RD-221). Yellow To separately sold power supply wiring kit (RD-221). Cap (1*) When not using this terminal, do not remove the cap. Black (ground) To vehicle (metal) body. For more detail, please refer to RD-221 owner’s manual. Relay Yellow Power is always supplied to this terminal. Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF. Red Power is supplied to this terminal when the ignition key is in the ACC or ON position. Fuse (1A) Fuse (20 A) Power supply wiring kit “RD-221” (sold separately) Multi-CD player (sold separately) Black (ground) To vehicle (metal) body. Red IP-BUS input (Blue) Orange/white To lighting switch terminal. ISO connector Note: In some vehicles, the ISO connector may be divided into two. In this case, be sure to connect to both connectors. Yellow/black If you use a cellular telephone, connect it via the Audio Mute lead on the cellular telephone. If not, keep the Audio Mute lead free of any connections. Speaker leads White : Front left + White/black : Front left . Gray : Front right + Gray/black : Front right . Green : Rear left + or Subwoofer + Green/black : Rear left . or Subwoofer . Violet : Rear right + or Subwoofer + Violet/black : Rear right . or Subwoofer . Red Not used. Yellow Not used. Blue/white (7*) To Auto-antenna relay control terminal (max. 300 mA 12 V DC). Blue/white (6*) Blue/white To system control terminal of the power amp (max. 300 mA 12 V DC). IP-BUS cable This product Antenna jack Refer to page7-8. 15 cm Fuse resistor Fuse holder Fuse holder The pin position of the ISO connector will differ depends on the type of vehicle. Connect 6* and 7* when Pin 5 is an antenna control type. In another type of vehicle, never connect 6* and 7*. Jack for Wired Remote Control Please see the Instruction Manual for the Wired Remote Control (sold separately...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории