When “RE-ENTER” is displayed, “CODE” is also displayed. 7 Do the step 5 through 6 operation, and reenter the Security Code. “APPROVED” is displayed. The Security Code function activates. . • If you enter the wrong Code in steps 5 through 6, repeat from step 5. • When the Security Code function is activated, “CODE SET” changes to “CODE CLR”. • To deactivate the Security Code function, see the next section . 8 Exit Security Code mode Press the Search button. 10 | KDC-MP5043U/ KDC-MP543U/ KDC-MP443U Entering Security Code The Security Code is required to use the audio unit when the unit is first used after removed from the battery power source or the Reset button is pressed. 1 Turn the power ON. 2 Do the step 5 through 6 operation, and enter the Security Code. “APPROVED” is displayed. Now, you can use the unit. Deactivating Security Code To deactivate the Security Code function. 1 Select Standby Press the [SRC] button. Select the “STANDBY” display. 2 Enter Menu mode Press the Search button for at least 1 second. “MENU” is displayed. 3 Select Security Code mode Press the [FM+] or [AM–] button. Select the “CODE CLR” display. 4 Enter Security Code mode Press the [AUD] knob for at least 1 second. When “ENTER” is displayed, “CODE CLR” is also displayed. 5 Enter Security Code Select the digits to enter Press the [4] or [.] button. Select the Security Code Press the [FM+] or [AM–] button. numbers Operation type Operation 6 Press the [AUD] knob for at least 3 seconds. “CLEAR” is displayed. The Security Code function deactivates. 7 Exit Security Code mode Press the Search button. . • If a wrong security code is entered, “ERROR” is displayed. Enter a correct security code. Demonstration mode setting Setting the demonstration mode as follows; “DEMO ON” The Demonstration mode function is ON. “DEMO OFF” Exit Demonstration mode (Normal mode). Display Setting 1 Enter Menu mode Press the Search button for at least 1 second. “MENU” is displayed. 2 Select Demonstration mode Press the [FM+] or [AM–] button. Select the “DEMO” display. 3 Set the Demonstration mode Press the [AUD] knob for at least 2 seconds. 4 Exit Demonstration mode Press the Search button. English | 11 Audio Adjustments Audio Control You can adjust following Audio Control items; Adjustment Item Display Range Subwoofer level “SW L” –15 — +15 Bass Boost “B.BOOST”/ “B.B” “1”/”2”/“OFF” (The indicator turns on according to the setting.) System Q “NATURAL”/ “ROCK”/ “POPS”/ “EASY”/ “TOP40”/ “JAZZ”/ “GAME”/ “USER” Natural/Rock/Pops/Easy/ Top 40/Jazz/Game/User setting Bass level* “BAS L” –8 — +8 Middle level* “MID L” –8 — +8 Treble level* “TRE L” –8 — +8 Balance “BAL” Left 15 — Right 15 Fader “FAD” Rear 15 — Front 15 Exit Audio Control mode (Volume control mode) * Source tone memory: Puts the set up value in the memory per source. . • “USER”: This appears when Bass level, Middle level, and Treble level are adjusted. When “USER” is selected, these levels are recalled. 1 Select the source to adjust Press the [SRC] button. 2 Enter Audio Control mode Press the [AUD] knob. 3 Select the Audio item to adjust Press the [AUD] knob. 4 Adjust the Audio item Turn the [AUD] knob. 5 Exit Audio Control mode Press any button. Press a button other than the [AUD] knob. Audio Setup You can set Sound system, such as follows; Low Pass Filter “LPF” 80/120/160/Through(OFF) Hz Volume offset “V-OFF” –8 — ±0 (AUX: –8— +8) Adjustment Item Display Range . • Volume offset: Sets each source’s volume as a difference from the basic volume. 1 Select the source to adjust Press the [SRC] button. 2 Enter Audio Setup mode Press the [AUD] knob for at least 1 second. 3 Select the Audio Setup item to adjust Press the [AUD] knob. 4 Adjust the Audio setup item Turn the [AUD] knob. 5 Exit Audio Setup mode Press the [AUD] knob for at least 1 second. Speaker Setting Fine-tuning so that the System Q value is optimal when setting the speaker type as follows; OFF “SP OFF” For 5 & 4 in. speaker “SP 5/4” For 6 & 6x9 in. speaker “SP 6*9/6” For the OEM speaker “SP OEM” Speaker type Display 1 Enter Standby Press the [SRC] button. Select the “STANDBY” display. 2 Enter Speaker Setting mode Press the [AUD] knob. 3 Select the Speaker type Turn the [AUD] knob. 4 Exit Speaker Setting mode Press the [AUD] knob. 12 | KDC-MP5043U/ KDC-MP543U/ KDC-MP443U Basic Operations of remote control In Tuner source SRCVOLATTAUDATT SRCVOL .. Not used. SRCVOLATTAUDATT SRCVOL .. Not used. Band select: [FM+]/[AM–] Station select: [4]/[.] AUD FM/AM KDC-MP5043U/ KDC-MP543U: Recall preset stations: [1] — [6] In CD/USB source KDC-MP443U: Music select: [4]/[.] Folder/Disc select: [FM+]/[AM–] 0 — 9 General control Volume control: [VOL] Source select: [SRC] Volume reduce: [ATT] When the button is pressed again, the volume returns to the previous level. In Audio control Audio item select: [AUD] Adjust the Audio item: [VOL] . • Refer to
