Оценок - 3, средний балл: 3
(
)
)
|
Фрагмент инструкции
8. Press the left part at the upper side of the faceplate once to make the faceplate control panel appear. 2CAUTION • If your car's ignition does not have ignition wires to a power source that with the ignition key. If you connect the ignition wire to a source with a constant voltage supply, as with battery wires, the battery may die. • If the console has a lid, make sure to install the faceplate will not hit the lid when closing and opening. • If the fuse blows, first make sure the wires aren’t touching to cause a short circuit, then replace the old fuse with same rating. • Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. • When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. • Mount the unit so that the mounting angle is 30° or less. — 23 — Connecting Connecting ANT. CONT ILLUMI P.CONT FRONT • L FRONT • R – + FRONTREAR FM/AM antenna input Rear left output (White) Rear right output (Red) Fuse (10A) (Accessory1) Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) - (To car chassis) Ignition key switch 41 Car fuse box (Main fuse) 42 ACC 44 Car fuse box 45 If no connections are made, do not let the wire come out 3 Front left output (White) Front right output (Red) Power control wire (Blue/White) 16 Motor antenna control wire (Blue) 17 Dimmer control wire (Orange / White) 19 4 When using the optional power amplifier, connect to its power control terminal. 7 To car light control switch 5 Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. Wiring harness White/Black White Gray/Black Gray Green/Black REAR • L Green Purple/Black REAR • R Purple To KENWOOD disc changer/ DAB control input/ KPA-SD100/ KPA-HD100/ KPA-SS100 To connect these leads, refer to the relevant instruction manuals. To front left speaker To front right speaker To rear left speaker To rear right speaker Battery — 24 — Installation Installation Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in Phillips truss head sheet metal screw (commercially available) Screw (M4X8) (commercially available) Installation Installation Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in Phillips truss head sheet metal screw (commercially available) Screw (M4X8) (commercially available) place. (commercially available) Metal mounting strap Accessory6 Factory-installed Firewall or metal support J-Car Bracket Radio Bracket Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). To attach this unit, make sure the front of the control panel faces you and fit it into the mounting sleeve by pressing the four corners of the hard rubber frame at the same time. Do not apply strong pressure to other sections than the corners; otherwise troubles such as the impossibility of opening or closing the panel may result. R L 8mm 5mm 5mm 8mm For Nissan Car After aligning the J-Car bracket with the factory-installed radio bracket, tighten the screws. Accessory4 for Toyota car Accessory3 for Nissan car Factory trim bezel (follow indications for L/Accessory7 J-Car Trim Plate (place thick part on bottom) Factory-installed Radio Bracket For Toyota Car After aligning the factory-installed radio bracket, tighten the screws. Damage to the unit will result from using screws other than those provided. A pair of J-Car Brackets (Accessory 6) are not used when fitting in a Toyota car. — 25 — English English 1 Insert the removal indentations in the frame, and pull it gently lock is released. 2 Remove the screw (M4X8) on the back panel. 3 Insert the two removal tools deeply into the slots on each side, as shown. 4 Push upward the removal tool toward the top, and pull out the unit halfway while pressing towards the inside. Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. Accessory8 Removal tool Screw (M4X8) (commercially available) Accessory2 Removal tool If you want to lock off, follow the directions 1 Refer to the function "Removing remove the faceplate. 2 Insert the provided screw into bottom side of th...
Эта инструкция также подходит к моделям:Автомагнитолы - KDC-5019 (1.7 mb)