The ignition and battery wire are incorrectly connected. . Connect the wire correctly, referring to the section on . ? The TEL mute function . The TEL mute wire . Connect the wire correctly, referring to the section . ? The TEL mute function turns not connected. . The TEL mute wire is touching a metal . Pull the TEL mute wire away from the ? No sound can be heard, or the volume . The fader or balance settings are set all the . Center the fader and balance settings. . The input/output wires or wiring harness are connected . Reconnect the input/output wires or the wiring harness See the section on "Connecting Wires to Terminals". . The cassette tape is bad. . Try playing another cassette tape. If works fine, the first tape was bad. ? The sound quality is poor or distorted. . One of the speaker wires is being pinched by a screw in the car. . Check the speaker wiring. . The tape head is dirty. . Clean the tape head. . The speakers are not wired correctly. . Reconnect the speaker wires so that each output terminal is connected to a different speaker. ? The Touch Sensor Tone doesn’t sound. . The preout jack is being used. . The Touch Sensor Tone can’t be output from the preout jack. ? Even though Synchronize Clock is ON, the clock can’t be adjusted. . The received RDS station isn’t sending time data. . Receive another RDS station. — 28 — Tuner source Tuner source ? Radio reception is poor. ? "AUX" is displayed . The car antenna is not extended. . O-N switch is set to "O" . Pull the antenna out all the . Set the switch to "N" side. . The antenna control wire is not . Connect the wire correctly, referring to the section on . ? It isn't the set Traffic information sound volume. . The set sound volume is less than the tuner . If the tuner sound volume is louder than the tuner sound volume is used. Cassette tape source ? Can’t remove tape. . The cause is that more than 10 minutes has elapsed since the ACC switch was turned OFF. . The tape can only be removed within 10 minutes of the ACC switch being turned OFF. If more than 10 minutes has elapsed, turn the ACC switch ON again and press the Eject button. ? The Tape Advance and Music Repeat don’t operate correctly. . The space between the songs on the tape can’t be recognized because it’s too short. . Have at least 4 seconds between songs. . The space between songs can’t be recognized because there’s too much noise between songs. . Reduce the noise between songs. ? The blank skip doesn’t work. . Because noise is too loud, the non-recorded part can’t be recognized. . Reduce the noise between songs. ? Blank Skip functions at places that are recorded. . Because the recording level is low, it’s recognized as not recorded. . Turn Blank Skip OFF. . Unsupported disc changer is connected. . Connect the supported disc changer. (page 3) ? The specified disc does not play, but another one plays instead. . The specified CD is quite dirty. . Clean the CD. . The CD is upside-down. . Load the CD with the labeled side up. . The disc is loaded in a different slot from that specified. . Eject the disc magazine and check the number for the disc. . The disc is severely scratched. . Try another disc instead. ? The specified track will not play. . Random play or magazine random play has been selected. . Turn off random play or magazine random play. ? Track repeat, disc repeat, track scan, random play, and magazine random play start by themselves. . The setting is not canceled. . The settings for these functions remain on until the setting to off or the disc ejected, even if the power is turned off or the source changed. ? Cannot play CD-R or CD-RW. . Finalization processing is not being conducted for CD-R/CD-RW. . Conduct finalization processing with CD recorder. . A non-compatible CD changer is being used to play the CD-R/CDRW. . Use a CD changer compatible with CD-R/CD-RW to play. ? Track Search can't be done. . For the albums first or last song. . For each album, Track Search can't be done in the backward direction for the first song or in the forward direction for the last song. — 29 — English English If the following center: • Even though the disc changer not ON, with "AUX" showing • Even though no device (KCA-KDC-CPS85, KDC-CX85, KDC-Auxiliary input is entered when switching The following messages are displayed system condition. EJECT: No disc magazine has been loaded in the changer. The disc magazine is not completely loaded. . Load the disc magazine properly. No CD in the unit. . Insert the CD. NO DISC: No disc has been loaded in the disc magazine. . Load a disc into the disc magazine. E-04: No disc has been loaded in the disc magazine. . Load a disc into the disc magazine. The CD is quite dirty. The CD is upside-down. The CD is scratched a lot. . Clean the CD and load it correctly. BLANK: Nothing has been recorded on the MD. NO TRACK: No tracks are recorded on the MD, although it has a titl...
)
