Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
factory radio). This connection will allow you to connect directly to the speaker output of the radio with out the need of an external adapter. Determine the type of radio you have and make one of the following connections. HIGH LEVEL CONNECTIONS (OPTIONAL) CAUTION! Before making any connections determine the type of radio to avoid possible damage to amplifier and/or radio. TWO CHANNEL CONNECTIONS: FLOATING GROUND RADIO (MOST COMMON TYPE) RIGHT + RIGHT - LEFT - GREEN LEFT + GREEN/BLACK (NOT USED) GRAY/BLACK BLACK GRAY 94.7 GREEN BLACK GRAY/BLACK NOT USED GREEN/BLACK NOT USED GRAY RIGHT + LEFT + GROUND 94.7 TWO CHANNEL CONNECTIONS: COMMON GROUND RADIO GRAY BLACK GRAY/BLACK (NOT USED) WHITE RIGHT + LEFT + GROUND WHITE BLACK GRAY/BLACK (NOT USED) WHITE/BLACK (NOT USED) GRAY RIGHT + WHITE/BLACK (NOT USED) LEFT + GROUND POWER BASS BOOST BASS BOOST 0dB 12dB 0dB 12dB X-OVER X-OVER 60Hz 400Hz 60Hz 400Hz LEVEL INPUT HI INPUT HI INPUT REMOTE CH1 CH2 CH3 CH4 MIN MAX LEVEL MIN MAX FILTER LOW FLAT HI FILTER LOW FLAT HI 9 ELA / MAA60.4 CONNECTIONS: COMMON GROUND RADIO 94.7 ELA / MAA60.4 CONNECTIONS: FLOATING GROUND RADIO (MOST COMMON TYPE) RIGHT + RIGHT - LEFT - LEFT + GRAY GRAY/BLACK (NOT USED) WHITE/BLACK BLACK (GROUND) WHITE RIGHT + RIGHT - LEFT - LEFT + GRAY GRAY/BLACK (NOT USED) WHITE/BLACK BLACK (GROUND) WHITE 94.7 POWER BASS BOOST BASS BOOST 0dB 12dB 0dB 12dB X-OVER X-OVER 60Hz 400Hz 60Hz 400Hz LEVEL INPUT HI INPUT HI INPUT REMOTE CH1 CH2 CH3 CH4 MIN MAX LEVEL MIN MAX FILTER LOW FLAT HI FILTER LOW FLAT HI +12V REM SPEAKER 15A 15A 15A 15A FUSE GND ELA150.1, ELA300.1 AND ELA /MAA500.1 SPEAKER CONNECTIONS 4 Ohm Speaker (2 Ohm Minimum) Make the speaker connections using speaker wire that is at least 16 gauge or heavier. As with any audio component, proper phasing of the amplifier and speakers is essential for strong bass response. When connecting, make sure that positive (+) from the amplifier is connected to the positive (+) of the speaker, and the same for negative (-). SPEAKER CONNECTIONS BRIDGED CH 1 CH 2 CH 3 CH 4 AUX OUTPUT +12V REM GND 20A AUX 7.5A 20A AMP + - + - + - + - 4 Ohm Speakers (2 Ohm Minimum) 4 Ohm Speakers (2 Ohm Minimum) FOUR CHANNEL SPEAKER CONNECTIONS 10 TWO CHANNEL SPEAKER CONNECTIONS SPEAKERS BRIDGED AUX OUTPUT +12V REM 20A GND 4 Ohm Speakers (2 Ohm Minimum) + - + - BRIDGED CH 1 CH 2 CH 3 CH 4 AUX OUTPUT +12V REM GND 20A AUX 7.5A 20A AMP + - + - + - + - 4 Ohm Speaker 4 Ohm Speaker SPEAKERS BRIDGED AUX OUTPUT +12V REM 20A 20A AUX 7.5A 20A AMP GND + 4 Ohm Speaker TWO CHANNEL BRIDGED SPEAKER CONNECTIONS FOUR CHANNEL BRIDGED SPEAKER CONNECTIONS SPEAKER CONNECTIONS (BRIDGED) The EL amplifiers are capable of being bridged in a mono configuration. This feature allows you the flexibility of using the amplifier to drive a ** subwoofer or a center channel. In this configuration the amplifier sums the right and left channel to deliver one channel (mono) output. Please note: in order for the amplifier to sum right and left signal information, both right and left RCA connections must be made. **CAUTION! In the bridged mode, the amplifier must see a 4 Ohm load or higher. Any lower than 4 Ohms will cause the amplifier to overheat and possibly cause 11 SPEAKERS BRIDGED AUX OUTPUT +12V REM 20A 20A AUX 7.5A 20A AMP GND CAUTION! In Tri- mode operation, the amplifier must see a 2 Ohm load or higher for the stereo satellites and no lower than 4 Ohms for the subwoofer(s). Any lower than the above mentioned impedance will cause the amplifier to overheat and possibly cause permanent damage to the amplifier. SPEAKER CONNECTIONS (TRI-MODE) NON-POLAR CAPACITOR INDUCTOR (COIL) L E G E N D 100 F - + 100 F + - - 4 mH Left Mid / Tweete...
Эта инструкция также подходит к моделям:Автомагнитолы - ELA150.1 (4.25 mb)
Автомагнитолы - MAA500.1 (4.25 mb)
Автомагнитолы - MAA60.4 (4.25 mb)
Автомагнитолы - ELA500.1 (4.25 mb)