Войти:
Оценок - 0, средний балл: 0 ( )

Инструкция по эксплуатации Philips, модель CSP550/51

Производитель: Philips
Размер: 736.97 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Note • Make sure that nothing obstructs around the mounting location of the door. • A hole for mounting may already be cut out of the inner panel of the door (front or rear). In this case, you need to modify the board only. • Ensure that the speaker terminals, frame or magnet do not inter fere with any inner par ts, such as the window mechanism in the door (when you open or close the window), etc. Also ensure that the speaker grille does not touch any inner fittings, such as the window cranks, door handles, arm rests etc. Mount the woofer Option 1: Mount on door (front or rear) B You can mount the wooferss on the front/rear door of your car. a 1 Turn off the car ignition key. 2 If the power is on, the click noise generated by the connection • may damage the speakers. Cut out the mounting template from the packing box and paste it on the location selected for mounting the woofer. 3 Mark the cut-off hole and the 4 bolt holes. b 4 Cut out the marked area and drill the bolt holes. c 5 Remove the grille net. d 6 Connect the woofers to the network or car audio (see ‘Connect the woofer/tweeter to the network ’). 7 Mount on the speaker as shown below. e 8 Press and inser t the edges of the grille net. f Tip • The speaker grille can be mounted without the grille net, if you like. Option 2: Mount on rear tray C You can also mount the woofers into the sur face of the rear tray. Follow the steps in section “Option 1: Mount in door” to mount the speakers into the rear tray. Mount the Tweeter D Follow steps mentioned in “Mount the woofer” section to mount the tweeters. Mount the network E 1 Find a proper location to mount the networks. 2 Mount the networks onto the car with the supplied screws. Connect the woofer/tweeter to the network F Note • Match the “left”, “right”, “+” and “-” terminals correctly. Revised polarity may degrade sound quality. • Two 4-ohm speakers, wired in stereo, present a 8 ohm load to each channel of the amplifier. Most two channel amplifiers work well in this configuration. However, if two 4-ohm speakers, wired in parallel to a bridged two -channel amplifier, present a 2-ohm mono load to the amplifier. Most 2-channel amplifiers do not suppor t 2-ohm mono operation! Amplifier damage may result! 1 Connect the woofers and the tweeters to the 2-way crossover network first, then connect the network to your amplifier or car audio directly. 4. Product information Model CSP550 CSP650 CSP652 Speaker type 13cm, 2-way 16.5cm, 2-way 16.5cm, 2-way component speaker component speaker component speaker RMS power (Watts) 40W 50W 60W Peak music power (Watts) 210W 240W 300W Sensitivity (dB/W/m) 90dB 90dB 91dB Frequency response (Hz) 40-35kHz 36-35kHz 34-35kHz Impedance (ohms) 4 ohms 4 ohms 4 ohms Magnet mass (Oz) 11Oz 12.6Oz 18.8Oz Woofer mounting depth (mm) 52mm 61mm 63mm Tweeter mounting depth (mm) 19mm 19mm 19mm Note • Product information is subject to change without prior notice. 5.Troubleshooting To keep the warranty valid, never tr y to repair the...

Эта инструкция также подходит к моделям:
Автоакустика - CSP650/51 (736.97 kb)
Автоакустика - CSP652/51 (736.97 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории