Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
2 Press [PLAY MENU] repeatedly to select “A.PRESET” and then press [OK]. 3 Press [3, 4] to select “LOWEST” or “CURRENT” and then press [OK]. LOWEST: To begin auto preset with the lowest frequency (FM 87.9 or FM 87.5). CURRENT: To begin auto preset with the current frequency.* * To change the frequency, refer to “Manual tuning and presetting”. The tuner starts to preset all the stations it can receive into the channels in ascending order. Listening to a preset channel Preparation 1 Press [RADIO] to select “FM”. 2 Press [PLAY MENU] repeatedly to select “TUNEMODE” and then press [OK]. 3 Press [3, 4] to select “PRESET” and then • press [OK]. 1 Press [RADIO] to select “FM”. 2 Press [:/6] or [5/9] to select the channel. . Manual tuning and presetting Select a radio broadcast. 1 Press [RADIO] to select “FM”. 2 Press [PLAY MENU] repeatedly to select “TUNEMODE” and then press [OK]. 3 Press [3, 4] to select “MANUAL” and then press [OK]. 4 Press [:/6] or [5/9] to tune to the required station. 10 . To start automatic tuning, press and hold [:/6], [5/9] until the frequency starts scrolling. Tuning stops when a station is found. RQT9633 To preset the channel 5 While listening to the radio broadcast Press [OK]. 6 Press [3, 4] to select the channel and then press [OK]. . To improve FM sound quality 1 While receiving FM broadcasts, press [PLAY MENU] repeatedly to select “FM MODE” and then press [OK]. 2 Press [3, 4] to select “MONO” and then press [OK]. .This setting can be preset and memorized. To do so, continue to step 5 of “Manual tuning and presetting”. • Select “STEREO” in step2 to returnto stereo . “MONO” is canceled if the frequency is changed. . If “MONO” is selected,regardless of the type ofsignal . this unit is receiving, “FM MONO” is displayedwhen • • broadcasts. [DISPLAY] is pressed. (• below) . To display the current signal status Press [DISPLAY]. “FM ST”: The FM signal is in stereo. “FM”: The FM signal is in monaural. .“FM” is also displayed even if this unit is not tuned to a station. . “STEREO” is displayed when this unit tunes to a stereo broadcast. Internet Radio This unit can output Internet radio if “vTuner for Panasonic” is installed on your iPhone/iPod touch. Preparation .Install “vTuner for Panasonic” to your iPhone/ iPod touch. .Install iOS 5.0 or later. 1 Insert the iPhone/iPod touch to this unit. 2 Press [iPod] repeatedly to select “VTUNER”. {. “vTuner for Panasonic” starts. . Visit the below website for the following information about “vTuner for Panasonic”: (Compatible iPhone/iPod touch models and software versions, purchasing, installation and operation details.) . A pop-up screen may appear on your iPhone/iPod touch. Follow the indicated instructions. Sound adjustment Sound adjustment 1 Press [SOUND] repeatedly to select the effect and then press [OK]. 2 Press [3, 4] to select the setting and then press [OK]. *1: This function can also be selected with the [D.BASS] button on the unit. .You may experience a reduction in sound quality when these effects are used with some sources. If this occurs, turn the sound effects off. Clock and Timer Direct-Vocal Surround (D.SURROUND) “LEVEL 1”, “LEVEL 2” or “OFF”. .The factory preset is “OFF”. Preset EQ (PRESET EQ) “HEAVY” (heavy), “SOFT” (soft), “CLEAR” (clear), “VOCAL” (vocal) or “FLAT” (flat/off). .The factory preset is “HEAVY”. Bass (BASS) or Treble (TREBLE) Adjust the level (j4 to i4). Dynamic Bass*1 (D.BASS) “ON D.BASS” or “OFF D.BASS”. .The factory preset is “ON D.BASS”. Setting the clock This is a 12-hour clock. • 1 Press [SETUP] repeatedly to select “CLOCK” and then press [OK]. 2 Press [3, 4] to set the time and then press [OK]. . To display the clock, press [SETUP] repeatedly to select “CLOCK” and then press [OK] once. The time is displayed for 10 seconds. (During standby, press [iPod MENU, DISPLAY] once.) . The clock is reset when there is a power failure or when the AC power supply cord is removed. . Reset the clock regularly to maintain accuracy. Play timer You can set the timer so this unit turns on at a certain time every day. Preparation Set the clock (• left). . Setting the timer 1 Press [SETUP] repeatedly to select “TIMER ADJ” and then press [OK]. 2 Press [3, 4] to set the starting time (“ON TIME”) and then press [OK]. 3 Press [3, 4] to set the finishing time (“OFF TIME”) and then press [OK]. ENGLISH • To display the timer settings, press [SETUP] repeatedly to . select “TIMER ADJ” and then press [OK] once. (During standby, press [iPod MENU,DISPLAY] twice.) The music source and volume will also be displayed if the . • timer is turned on. (• below) . Turn the timer on 1 Select the music source*2 and set the desired volume. 2 Press [SETUP] repeatedly to select “TIMER SET” and then press [OK]. 3 Press [3, 4] to select “SET” and then press [OK]. . “F” is displayed. 4 Press [I] to turn the unit off. *2: “CD”, “IPOD” and “FM” can be set as the music source. . This unit can be used as normal after the timer i...