Оценок - , средний балл:
(
)
)
Производитель: Panasonic
Размер: 146.14 kb
Название файла: SBCR33.PDF
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
For optimum performance and safety, please read these instructions carefully. The model number and serial number of this product can be found on the back of the unit; and the serial number either on the back or the bottom. Please note them in the space provided below and retain this booklet as a permanent record of your purchase to aid identification in the event of theft. Model number Serial number Installation The sound reproduced by a speaker system is easily influenced by such factors as room acoustics and the system’s location in the room. Before finally deciding where the speakers are to be placed, please read the following information carefully. • The bass sound will be increased if the speakers are placed on the floor or close to a wall due to the reflection of sound. It is, therefore, possible to adjust the bass sound to some extent by adjusting the speaker's distance from the wall and /or floor. • Undesirable resonance of sound reflection will occur if the speakers face a hard wall or window. Curtains or similar materials can be used to prevent these reflections. • To prevent possible acoustic feedback, the speaker systems should be kept away from the turntable. This feedback (howling) can result from vibrations from the speakers. The turntable should, therefore, never be placed on the same surface as the speaker system. A thick piece of felt or similar material can be used under the turntable to reduce howling. Closing the turntable’s cover also reduces this problem. Connecting the speaker system Before connecting the speaker systems to the amplifier, please check the following: • Be sure to switch OFF the power to the amplifier. • Use with an amplifier having 8ft or below impedance speaker terminals. • Be sure to only connect positive (+) wires to positive {+) terminals, and negative (—) wires to negative (—) terminals. Speaker connection cables (not included) 2 15 mm Note: To prevent damage to circuitry, never short-circuit positive ( + ) and negative (—) speaker wires. 1. Twist the core of the connection cables. 2. Press the pushbutton, and insert the core until it can no longer be seen. 3. Release the pushbutton, and pull the cable gently to be sure that it is secured. Power-handling capacity The power-handling capacity of this unit is indicated in the specifications. The amplifiers volume control should be set to avoid an excessive input level. This is specifically true of amplifiers having an output power rating higher than that of the speaker system. Even if the amplifier to be used has an output power rating lower than the speaker system, the amplifier output may become distorted. This "clipping" distortion creates an excessive input level which can damage the speaker system. This type of distortion also occurs if the input signal to the amplifier is too large. Bass and treble controls also increase the level of the input signal to the speaker system, so care should be taken to adjust the volume to a proper level. The volume level of the amplifier should be reduced if the following signals are to be applied to the speaker system: Interstation noise of the FM radio band; output from a tape deck during rewind or fast forward; acoustic feedback from a microphone or musical instrument; electrical noise from the connection or disconnection of a phono cartridge, or phono or RCA cables. This unit incorporates electronic circuitry that automatically protects the speakers when a safe overall input level has been exceeded. When the protection circuit is activated, the sound from the speakers can be interrupted. If the speakers sound is interrupted, do not operate the system continuously. Proceed as follows: 1. Reduce the volume setting of the amplifier. 2. Check whether or not there is any abnormal condition of the equipment used as the sound source, or of the connections. 3. If there is no abnormal condition, the protection circuitry will be automatically reset in a few minutes. After the protection circuit is reset... Do not increase the amplifier’s level too high. 3 Maintenance Although the enclosure and the speaker units of this speaker system are made of carefully selected materials and have been produced using the finest manufacturing techniques, sudden changes in surrounding temperature and / or humidity should be avoided. Keep this unit away from sources of heat, high humidity and direct sunlight. • The speaker system should not be placed near a TV. The speaker magnet may cause a disturbance in the TV picture. • If the enclosure becomes dirty, use a soft, dry cloth to wipe it clean. If the dirt is excessive, soak a soft cloth in a weak solution of soap and water, wring it thoroughly before use. A soft dry cloth should then be used to wipe it dry. • Never use alcohol, paint thinner, benzine or other volatile chemicals to clean this unit because the may damage the finish, causing it to lose its luster. Also never use a wet or chemically-impregnated cl...