Оценок - 5, средний балл: 4
(
)
)
|
Фрагмент инструкции
- 10° 2 1 3 o3,5 mm ML 5000 Mute Loudspeaker Option: B C3C2 A 4-8 GPS NAV 12V10 A A1 A7 A2 A3 A5Accessory A6 A8 A4 B4 0 20 40 60 80 100 120 140 160 053.450.30 20 40 60 80 100 120 140 160 053.450.3R 12345TMC Receiver Multimedia A' B' C' AB IMPORTANT NOTES A Installation may only be carried out by trained specialists! A Observe all quality standards of the automobile industry! A Fire hazard! When drilling pay attention to the location of cable harnesses, tank and fuel pipes! A Never drill into car parts which are load bearing or are important for safety reasons! When installing components in the interior of the car remember the following: A The driver’s field of vision must not be obstructed! A Increased risk of injury in accidents! Do not mount components in an area where the airbag will inflate or where head or knees could impact in the event of an accident! A Installation may only be made in vehicles with 12 V board voltage and negative pole on car body. Installation in unsuitable vehicles could result in malfunction, damage or fire! System components At least the following components are required for installation. – Navigation computer with universal mounting frame and 2 release clips – Mounting brackets and installation material – GPS antenna with metal plate and cable – Power supply cable – Signal cable – IR remote control – Monitor with monitor cable – Map DVD/CD and Operating Software CD Take safety precautions A Before starting work disconnect the negative car battery terminal! When doing so make sure to observe manufacturer’s safety instructions (alarm system, airbag, immobilizer, radio coding, etc.)! Installing metal sleeve, ill 1 - 2 The computer can be mounted in a DIN radio opening of the vehicle with the supplied metal sleeve. Please note before mounting, ill. 3: – To ensure access to the DVD/CD opening a free space of at least 130 mm has to be in front of the navigation computer. – For sufficient air circulation a free space of at least 50 mm has to be behind the navigation computer. – A stable connection to the car body is necessary for the computer to function correctly! 2 English Horizontal mounting, ill. 3 The navigation computer has to be installed in horizontal position. A deviation of –10 to + 30 degrees can be adjusted within the diagnosis menu (see “Initial start-up”). Greater deviations can cause malfunctions. Insert metal sleeve into the DIN opening and press appropriate tags outwards with a screwdriver. Take care not to damage hidden parts in the dashboard. Securing the computer using the mounting brackets If installation of the navigation computer in a DIN slot is impossible or undesirable, it can be installed in alternative installation locations using the supplied mounting brackets (e.g., in the glove box, in the luggage compartment or under the seats). For this purpose, both side-mounted catch springs must be removed from the navigation computer. The two Torx screws are required later for securing the mounting bracket. Attaching mounting brackets, ill. 4 1. Position the brackets with the punched out tab at the right (or left) rear edge of the computer housing. It must be ensured that the tab fully engages with the sheet metal of the computer housing. 2. Swing the bracket forwards, applying pressure to the rear edge of the bracket so that it is flush with the computer housing. 3. Fasten the brackets to the computer housing using the existing Torx screws. The computer can then be secured in the desired installation location using the screws supplied. Suspended installation If suspended installation is required for the computer (e.g., under the rear shelf), the mounting brackets can be attached to the computer in the reversed position. Installing GPS antenna, ill. 6 The GPS antenna can be mounted in the vehicle interior, for example on the dashboard or on the hatshelf. The antenna must have clear “view” of the sky. – Clean the mounting surface and attach the antenna with the double-sided adhesive tape. – In vehicles with metallic window tinting the GPS antenna should be mounted outside on the vehicle body, for example on the roof or in the plastic bumper. Notes: To ensure perfect function please keep a distance of at least 10 cm to metal parts like window frame. Mounting temperature should be at least 60 degrees Fahrenheit to ensure the full adhesive effect of the tape. Mounting monitor A Never install the monitor in an area where the head could impact in case of an accident! A Observe safety standards concerning the driver’s field of vision and airbag inflation area! The monitor can be fastened with a support which is available on the market for accessories. Depending on the type of monitor (4:3 or 16:9 display) you use you can select the rectification for guidance pictograms. The system is adjusted to a 16:9 diplay by factory default. Installing holder for the remote control (optional), ill. 8 - 9 Mounting on angle bracket Screw holder to angle bracket. Either insert angle brack...