Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
-Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. POWER SOURCES 1. Power of Main Base The main base is operated by AC power. AC adaptor Input: 120V ~ 60Hz Output: 9V 1500mA Power installation: Insert the AC adaptor plug into DC Jack at the rear side of base. 2. Power of Individual Speaker Each speaker has 1 built-in rechargeable lithium battery for independent playback. Before the first use, we recommend to charge each speaker for 4 hours. When speaker is placed on the powered base(Power ON/OFF switch turns to blue), charging will start automatically. The charging LED indicator is in red color during charging, and will turn green afterwards. 3. Power of Remote Control To use the remote control, please ensure the remote control battery CR2025 (included) is installed properly. Replace the remote control battery when it stops working. It is highly recommended to use a good quality button cell. Note: Room lighting and battery life can affect the operating range of remote control. 4 ACCESSORIES Please see below items are included in the package: 1.ACAdaptor 2.AUX in Cord (3.5mm) 3. Remote Control (include button cell CR2025) 4. User Manuals (English and Spanish) 5. Warranty Card LOCATION OF CONTROL 1. Base (Top View) 2. Base (Rear View) 5 3. Speaker Unit 4. Remote Control GENERAL OPERATION 1. Select a proper docking adaptor (enclosed when purchase an iPod) and place it into the base, then dock your iPod gently. 6 2. Plug the AC adaptor plug into DC power Jack at the rear side of base. 3. Press the power button on the base or remote control to turn the unit on. Switch on the speakers to play your iPod. Choose the best channel through the “Channel” button at the rear of the base until the speakers receive the right signal. 4. Press ‘Vol+” or ‘Vol-‘ to choose a proper volume level, then you should now be able to take the speakers freely from room to room without disruption (Subject to its surroundings, approximately 100 feet in the open area without any interference). 5. If using iPod shuffle or other audio source with 3.5 mm headphone output jack, connect it to the AUX line in jack on the rear of base. (AUX in will not work when an iPod is docked) 6. Press the power button on the base or remote control to turn off the unit. TROUBLESHOOTING GUIDE Should you experience difficulties in the use of this player, please refer to the following chart or call 1-800-777-5331 for Customer Service. Symptom Possible problem Solution The base does not switch on (no power) AC adaptor is not plugged into a wall outlet or the connector is not plugged into the DC jack on the back of the unit. Plug the AC adaptor into a wall outlet and plug the connector into the DC jack on the unit. Wall outlet is not functioning. Plug another device into the same outlet to confirm the outlet is working. Using no/wrong iPod cradle. Make sure the dock cradle is the proper fit for your iPod. iPod does not respond to the speaker system iPod is not installed properly. Remove your iPod from the dock and check for any obstruction on the connectors in the docking and on your iPod. Then reseat it in the dock. Your iPod is locked up. Please make sure that your iPod is 7 working properly before docking into the unit. iPod does not charge up iPod is not installed properly. Remove your iPod from the dock and check for any obstruction on the connectors in the docking and on your iPod. Then reseat it in the dock. iPod battery has problem. Please make sure your iPod is working properly before docking into the unit. Speakers do not play the sound from docked device Speakers receive signal from other devices, or the other set of JiSS-585 Slide the channel switch to select another channel. Place the unit to a location where receive lesser external signal. Sound is cut off or noisy The unit experiences interference Move the channel switch from one channel to the other channel (3 for selection) at the rear of base for the best reception. Do not turn on other wireless devices simultaneously. Sound is distorted Sound source is distorted. If the source is iPod, try to check the sound at personal computer before putting into the iPod. If you are using an external sound source like digital audio player, try reducing the output volume on the device itself. Also try turning bass boost OFF or change the EQ setting. Volume level is set too high. Decrease the volume. 8 SPECIFICATIONS Power Supply Power adaptor (included): Input AC 120V ~ 60Hz Output DC 9V 1500mA Power of remote control: 1 x DC 3V CR2025 button cell (included) Frequency RF Channel Transmission: 915.0MHz (Channel 1) 914.5MHz (Channel 2) 914.0MHz (Channel 3) SERVICE Please refer t...