Оценок - 5, средний балл: 4.2
(
)
)
|
Фрагмент инструкции
9. Open one packet of high-temperature grill cleaner, (several cleaners may be available on the market), and empty the contents into a suitable container. (One packet will clean one grill.) 10. Firmly attach a no-scratch pad to a pad holder. 11. Dip the no-scratch pad into the grill cleaner, and spread a light coating of grill cleaner over the entire platen surface, back, front, and side edges of both upper platens. DO NOT SCRUB. 12. After applying the grill cleaner, lightly scrub the platen surfaces, BACK, FRONT AND SIDE EDGES with the no-scratch pad until all the soil has been liquefied by the grill cleaner. For stubborn soils, apply additional grill cleaner and lightly scrub. DO NOT RINSE THE PLATENS AT THIS TIME. 13. Starting at the back of the lower grill, spread a light coating of grill cleaner over the entire surface. DO NOT SCRUB. 14. After applying the grill cleaner, lightly scrub the grill surface with the No-Scratch Pad until all the soil has been liquefied. 15. Rinse the upper platens with a dripping wet cloth. 16. Carefully pour small quantities of lukewarm water onto the grill while brushing the surface, backsplash, and bullnose with a pot brush or equivalent high-temperature brush. Continue until the water no longer boils away and the grill remains wet. Squeegee dry. Caution: Ice, cold water, or large quantities of water must never be applied to the grill plate or upper platen. Severe damage to the grill will occur! 17. Clean the release sheets as follows: A) Place the sheets on the lower grill. Scrub both sides of the sheets with the same no-scratch pad used on the grill. B) Rinse both sides of the sheets with a clean, wet cloth. 18. Rinse the lower grill by flooding the surface twice with lukewarm water. Squeegee after each rinse. 19. Wipe the lower grill surface, backsplash, bullnose, and hood with a clean, damp cloth. 20. When cleaning is completed, you may turn the “MASTER POWER” (rocker) switch off. AFTER CLEANING, apply a thin coat of fresh shortening to the lower grill surface only. Wipe down the surrounding areas. Empty, wash, rinse, and replace the grease troughs. Platen Zeroing: Turn Master power switch “ON”, wait for controllers to display “OFF”. 1. Press and hold for three, (3) seconds. “ENTER CODE” will be displayed. 2. Using the Gap Setting buttons, enter the code, (1251). “ENTER CODE **** ” will be displayed. 3. Press to enter the Programming Mode. “PROGRAMMING MODE MENU ITEMS” will be displayed. 4. Press two, (2) times in succession to display “PROGRAMMING MODE SYSTEM SETUP.” 5. Press six, (6) times. “PLATEN SET +/- XX” will be displayed. (XX=numbers that will vary from grill to grill.) Page 14 Part # 4517125 (09/03) CLEANING AND MAINTENANCE continued 6. Allow time for grill to heat and turn ready. Press both the Cancel (Green) and Standby (Black) buttons simultaneously to lower the upper platen. Press the Cancel (Green) button to raise the platen. Now, press both the Cancel (Green) and (Black) Buttons to re-lower the platen. 7. Remove platen adjuster caps from all four adjustment points on each platen. Remove the four locking caps from the adjustment points. 8. Using the adjusting tool lower platen until adjusting tool touches the arm assembly. 9. With gapping tool, adjust right rear of platen until the gapping tool fits snugly between the upper platen and grill surface. 10. Move next to the left front adjuster and raise the platen until the gapping tool fits snugly between the upper platen and grill surface. 11. Next go to the left rear adjuster and raise the platen until the gapping tool fits snugly between the upper platen and grill surface. 12. Move next to the right front adjustment and raise the platen until the gapping tool fits snugly between the upper platen and grill surface. 13. Repeat steps 9-12 one or more times until gapping tool fits snugly between the upper platen and grill surface at all four adjustment points without further adjustment. (See diagram below.) 14. Replace the platen adjuster locking caps “hollow side down” and tighten snugly. Replace platen adjuster caps. 15. Repeat steps 9-14 for each platen. Insert gap tool directly below platen adjusters. Part # 4517125 (09/03) Page 15 Page 16 Part # 4517125 (09/03) PROGRAMMING Programming Modes/Menu Sequence: Part # 4517125 (09/03) Page 17 PROGRAMMING continued PROGRAMMING continued Menu Items... To Change the Cook Time of a Product: 1. Press and hold for three, (3) seconds. “ENTER CODE” will be displayed. 2. Using the Gap Setting buttons, enter the code, (1251). “ENTER CODE **** ” will be displayed. 3. Press to enter the Programming Mode. “PROGRAMMING MODE MENU ITEMS” will be displayed. 4. Press . “MENU ITEMS STANDBY” will be displayed. 5. Use and to choose the desired Menu Item. 6. Press to display “(MENU ITEM) COOK TIME XX:XX” 7. Use and to adjust the cook time. 8. Press to save the changes. 9. Press to return to “PROGRAMMING MODE MENU ITEMS” 10. Press again to exit. To Turn Platen, (2-Sided), Cooking O...
Эта инструкция также подходит к моделям:Грили - XE24 (2.21 mb)