Оценок - 2, средний балл: 4 ( )

Производитель: Brinkmann Размер: 13.08 mb Название файла: Язык инструкции:

Step 8 Carefully replace each burner, making sure burner openings slide over valve nozzles. Screw each main burner "foot" down using screwdriver and screws that were set aside in Step 4. Replace cotter pin in side burner “foot” that were set aside in Step 2. Step 9 Replace warming rack, cooking grills, heat shields and grease tray. Note: Follow directions in the leak testing section of this manual before using this grill. L S Figure 1 Figure 2 Stop Plate Cooking Grills Heat Shields Warming Rack Tab Figure 3 Stop Plate Tab Cover Bolts Retaining Nut Brass Orifice 1.32mm Existing Rotisserie LP Gas Orifice Replacement Rotisserie Natural Gas Orifice (identified by number) Rotisserie Burner 1.32mm (YELLOW) 810-8550-S, 810-8552-S & 810-8555-S ROTISSERIE BURNERS CAUTION: Only use specified natural gas orifice for your grill. Note: It is helpful to keep the screws with the components as they are removed for ease of reassembly. Step 10 Remove the two screws of panel to gain access to the rotisserie LP valve on back side of grill. Set aside for later use. Step 11 Using an adjustable wrench to hold the gas line secure, use the open end wrench provided to loosen the gas line retaining nut. With the rotisserie gas supply line detached from the housing, use two wrenches to remove the LP brass orifice from the gas supply line. Replace the LP gas brass orifice with the proper natural gas orifice. (1.32mm YELLOW) Note: Bending the hose could damage the supply line. Step 12 Reattach gas supply line to the rotisserie housing by securing with the retaining nut removed in Step 11. Note: Leave the back panel off until the end of conversion and all gas leak testing has been completed. Step 13 Re-install rotisserie cover using the bolts that were set aside in Step 10. CAUTION: Some parts may contain sharp edges.Wear protective gloves if necessary. WARNING: Only use the specific orifice designated for your grill model. Always double check the millimeter size on the side of the orifice tip prior to installation. Use of any other orifice could lead to personal injury, property damage and void your grill warranty. Note: Make sure all control knobs are in the off position, LP tank valve is closed and tank is disconnected from regulator and removed from grill. Step 1 Using an adjustable wrench to hold the gas manifold connection secure, use a 3/4” wrench to loosen the hose connection nut. Replace existing LP hose/regulator assembly with natural gas 10’ hose assembly. Tighten the connection carefully using two wrenches. Step 2 Remove cotter pin from side burner "foot". Carefully lift side burner up and away from valve nozzle. Set aside for later use. Step 3 Open hood and remove warming rack, cooking grills and heat shields. Set aside for later use. 17 CONVERSION INSTRUCTIONS 810-8530-S & 810-8532-S Gas Manifold Nut Cooking Grills Heat Shields 10’ Natural Gas Hose Cotter Pin Warming Rack 18 Step 4 Remove screw from each burner "foot" using a screwdriver. Carefully lift each burner up and away from valve openings. Set aside for later use. Step 5 Use the gas orifice tool to remove the LP brass orifice from main burner valves through the hole on the firebox front panel. Repeat this step for all main and side burner valves in your grill. The side burner valve orifice is under the side shelf. Note: All orifices of the grill, except rotisserie, are double orifices type (LP gas and natural gas).You only remove the LP gas orifice tip. CAUTION: Some parts may contain sharp edges.Wear protective gloves if necessary. Step 6 Remove all the control knobs from the control panel and set aside for later use. LP Gas Orifice Gas Orifice Tool Side View Firebox Front Panel Stop Pin Figure 1 Stop Pin 19 Step 7 Figure 1 shows valve stem and bezel with the control knob removed.Take five large stop plates from the component card and place them over the main and side burner valve stems as illustrated (Figure 2).Take the small stop plate from the component card and place it over the rotisserie burner valve stem (Figure 3).Verify the tab and the stamped letter on the stop plates face out. Replace control knobs when finished. WARNING: We recommend and request t...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: