Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
If, after five minutes the flame is yellow, or there is a gap between the burner and the flame, adjust the burner (venturi) tube air shutter as follows: 1. Turn gas OFF and let the burner cool. 2. Beneath the control panel you can access the air shutter(s) which are located on the end of the burner tubes. 3. Loosen shutter set screw 4. Close the air shutter to the minimum opening. 5. Light the burner, wait five minutes and then carefully open the air shutter until the flame is blue and well defined. 6. Retighten the set screw. LIGHTINGSTICKR734KEEPHANDAWAYFROMTOPOFGRILLWHENLIGHTINGINFRAREDBURNERMATCHLIGHTHOLEBLUEFLAMEBURNER Figure 39 B101623-2-0112 OPERATION - PROPANE & NATURAL GAS GRILLS Before Cooking Before cooking on a grill for the first time, it should be operated to burn off any oil residue from the manufacturing process. 1. Raise the grill lid. 2. Light grill burners. 3. Burn on HI for ten minutes. 4. Close the lid and burn on HI for an additional ten minutes. 5. Turn OFF gas. The grill is now ready for use. Preheating Before cooking on a gas grill, allow the grill to preheat on HI for 5 minutes with the lid open. This uses very little fuel and provides better flavor. AVOID WATER DAMAGE TO BURNER! NEVER ALLOW WATER TO CONTACT THE BURNER AS DAMAGE WILL RESULT. WATER DAMAGE IS NOT COVERED BY YOUR BROILMASTER WARRANTY. WARNING! HOOD MUST BE OPEN WHEN LIGHTING GRILL BURNERS, WARMING UP THE GRILL, AND WHILE GRILLING. HOOD MAY ONLY BE CLOSED WHILE INFRARED IS IN USE AND BOTH KNOBS ARE SET ON "LOW," OR WHILE BLUE FLAME BURNER IS IN USE ONLY, OR WHEN THE GRILL IS NOT IN USE. B101623-2-0112 BLUE FLAME BURNER MAINTENANCE Cleaning the Grill Caution: To prevent injury, do not clean a hot grill. Note: Do not use a commercial cleaner on the cooking grids. Do not brush grids while they are hot. For baked on residue use a BRASS (NOT STEEL) brush on the cooking grid and other components. Burn Off This process is much like that used in self-cleaning ovens and is most efficient when completed after each use of the grill. Caution: Do not open the grill during the burn off process. Opening the grill during the burn off process may cause a sudden grease fire flare up that could burn your face and arms. Wait until the grill has cooled before opening. 1. Turn gas knob to HI. Close lid and allow the grill to burn for ten minutes, or until no smoke is present. Do not allow the grill to burn for more than 30 minutes. 2. Turn gas knob and supply to OFF and allow the grill to cool. 3. Wipe COOL grill with a damp cloth to remove soot. Grill Bottom Periodically remove cooking grids and Char-Master Briquets or flavor screen to clean the interior of the grill. Scrape off baked on residue with a putty knife or brass brush and rinse with water. Clean the bottom air holes with a small knife. Blue Flame Burner Maintenance Visually inspect the burner flames with each use. Five minutes after lighting, the flames should be blue and have well defined cones. See Figure 40. See the troubleshooting section if the flames are yellow or lift off the burner. Stainless steel burners often turn reddish brown after use. This does not effect the performance of the grill. When cleaning the interior of the grill, remove the burners and clean with a brass brush. Wash with water and a mild detergent. Grease Tray Empty periodically. Replacement tray liners can be purchased at most supermarkets where disposable aluminum baking pans are displayed. Burner (Venturi) Tubes The burner (venturi) tubes allow air and gas to mix prior to burning, thus ensuring an efficient flame. Spiders or other small insects may build webs or nests inside the tubes obstructing air flow. Fire, or flashback, can occur, in and/or around obstructed burner (venturi) tubes and can cause damage to components beneath the grill or an unsafe condition. To reduce risk, inspections and cleaning should be performed at least twice monthly when spiders are active. If the grill has been unused for an extended period of time inspect the tubes before using the grill. Clean burner (venturi) tubes as follows: 1. Remove the cooking grids and briquet rack (R3B only). 2. Remove the burner from the grill. 3. Use a small flexible brush to remove any debris from the burner (venturi) tube. 4. Flush with water. 5. Allow the burner (venturi) tube to dry before reinstalling. 6. Reinstall the burner, briquet rack and briquets and cooking grids. Exterior Clean regularly with a solution of mild detergent and hot water. Touch-up paint is available from your dealer. Broilmaster protective covers are recommended. Stainless steel components can be easily cleaned with a spray-on stainless steel cleaner found in most hardware stores. Char-Master Briquets If the briquets did not come clean during burn off, after cooling turn them over. The residue will burn off during warm-up for the next use. Correct Flame Pattern Incorrect Flame Pattern Figure 40 B101623-2-0112 INFRARED BURNER MAINTENANCE General Overview Proper care...
Эта инструкция также подходит к моделям:Грили - H3X-1 (9.89 mb)
Грили - H3XN-1 (9.89 mb)
Грили - H3XPK-1 (9.89 mb)
Грили - H4PK-1 (9.89 mb)