Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Do not use DC or any other voltage. Charge time will depend on battery type and capacity. Black & Decker three terminal slide pack batteries are designed for fast charging and most will be charged in one hour or less. Special high capacity batteries may take longer. Two terminal slide pack batteries will be charged at a slower rate to avoid overheating the pack. Most of these will be charged in 2 hours or less. READ ALL INSTRUCTIONS • Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode in a fire. • A small leakage of liquid from the battery pack cells may occur under extreme usage or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin: a. Wash quickly with soap and water. b. Neutralize with a mild acid such as lemon juice or vinegar. c. If battery liquid gets into your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention. (Medical Note: The liquid is 25-35% solution of potassium hydroxide.) • Charge the battery packs only in Black & Decker chargers. • DO NOT splash or immerse in water or other liquids. • Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 105°F (40.) (such as outside sheds or metal buildings in summer). DANGER: Electrocution hazard. Never attempt to open the battery pack for any reason. If battery pack case is cracked or damaged, do not insert into charger. Electric shock or electrocution may result. Damaged battery packs should be returned to service center for recycling. NOTE: Battery storage and carrying caps are provided for use whenever the battery is out of the tool or charger. Remove cap before placing battery in charger or tool. WARNING: Fire hazard. Do not store or carry battery so that metal objects can contact exposed battery terminals. For example, do not place battery in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc. without battery cap. Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools and the like. The US Department of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e., packed in suitcases and carry-on luggage) UNLESS they are properly protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit. Charging Procedure 1. Plug the charger into an appropriate outlet. NOTE: Do not charge by means of an engine generator or DC power source. Use only 120V AC. 2. Insert 1 or 2 batteries into the charger (Fig.1) . NOTE: Charge time is the same for multiple batteries. Be sure the pack(s) is fully seated in the charger. The red (charging) light will flash continuously indicating that the charging process has started. Fig.1 3. The completion of charge will be indicated by the red light remaining ON continuously. The pack is fully charged and may be used at this time or left in the charger. Charge Indicators Red light flashes continuously: Charging Red light remains ON continuously: Charged Red light flashing at a fast rate: Replace Pack The charger is designed to detect certain problems that can arise with battery packs which would be indicated by the red light flashing at a fast rate. If this occurs, re-insert battery pack. If problem persists, try a different battery pack to determine if the charger is OK. If the new pack charges correctly, then the original pack is defective and should be returned to a service center for recycling. If the new battery pack gives the same trouble indication as the original, have charger tested at an authorized service center. Red light flashes long, then short (dash dot, dash dot): Hot Pack Delay When the charger detects a battery that is hot, it automatically starts a Hot Pack Delay, suspending charging until the battery has cooled. After the battery has cooled, the charger automatically switches to the Pack Charging mode. This feature ensures maximum battery life. The red light flashes long, then short (dash dot, dash dot) while in the Hot Pack Delay mode. Wall Mounting (Figure 2) Mounting holes are provided for mounting the charger on a vertical surface. MOUNTING HOLES Fig.2 Leaving the Battery Pack in the Charger The charger and battery pack can be left connected with the red light glowing indefinitely. The charger will keep the battery pack fresh and fully charged. NOTE: A battery pack will slowly lose its charge when kept out of the charger. If the battery pack has not been kept on maintenance charge, it may need to be recharged before use. A battery pack may also slowly lose its charge if left in a charger that is not plugged int...
Эта инструкция также подходит к моделям:Зарядные устройства - 5147851-00 (266.24 kb)
Зарядные устройства - BDDC240 (266.24 kb)