Оценок - , средний балл: ( )

Инструкция по эксплуатации Lenmar Enterprises, модель 45005

Производитель: Lenmar Enterprises
Размер: 783.66 kb
Название файла: 40dabeb4-62ee-41fe-8265-9217bd0020a9.pdf

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

14. Use this product in accordance with the battery’s and vehicle’s instruction manual recommendations, safety warnings and charging instructions. 15. Never leave Battery Charger unattended. 16. Batteries can explode under certain conditions; excessive heat and/or poor ventilation can cause explosive gas buildup and battery explosion. Surges in electrical power supply could possibly cause battery explosion. Battery Charger should be plugged into a surge protection device. SKU 45005 For technical questions, please call 1-800-444-3353. Page 5 GROUNDING WARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician. GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS 1. Tools marked with “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. (See Figure A.) 2. The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool’s grounding system and must never be attached to an electrically “live” terminal. (See Figure A.) 3. Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (See Figure A.) FIGURE A FIGURE B DOUBLE INSULATED TOOLS:TOOLS WITH TWO PRONG PLUGS 4. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B.) SKU 45005 For technical questions, please call 1-800-444-3353. Page 6 5. Double insulated tools may be used in either of the 120 volt outlets shown in the following illustration. (See Figure B.) EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulatedtools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. (See Figure C.) 3. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See Figure C.) 4. When using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required. (See Figure C.) 5. If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size. (See Figure C.) 6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. 7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* NAMEPLATE AMPERES (At Full Load) EXTENSION CORD LENGTH 25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 0 -2.0 18 18 18 18 16 2.1 -3.4 18 18 18 16 14 3.5 -5.0 18 18 16 14 12 5.1 -7.0 18 16 14 12 12 7.1 -12.0 18 14 12 10 - 12.1 -16.0 14 12 10 -- 16.1 -20.0 12 10 --- FIGURE C * Based on limiting the line voltage drop to five volts at 150% of the rated amperes. SKU 45005 For technical questions, please call 1-800-444-3353. Page 7 SYMBOLOGY Unpacking When unpacking, make sure that the Battery Charger is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. Operation 1. Place the Battery Charger about six feet from the battery being charged. 2. If the battery to be charged is in a vehicle, verify that the ignition is off, remove vehicle’s cables from battery, then connect the positive (Red with +) Cable Clamp to the positive (+ or P) terminal of the battery. If necessary, clean the battery terminals.Wiggle the Cable Clamp on the battery terminal to get a good connection. 3. Connect...