Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
Colour of the replacement fuse cover must be the same colour as that visible on the pin face of the plug. Fuse covers are available from any good electrical store. IMPORTANT! FITTING A DIFFERENT PLUG As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: (See diagram). 1. Connect the green-yellow or green (Earth) wire to the terminal in the plug marked 'E' or with the symbol or coloured green and yellow or green. 2. Connect the blue (Neutral) wire to the terminal in the plug marked 'N' or coloured black. 3. Connect the brown (Live) wire to the terminal in the plug marked 'L' or coloured red. With alternative plugs a 13 A fuse must be fitted either in the plug or adaptor or in the main fuse box. If in doubt contact a qualified electrician. 3 TRANSPORTATION INSTRUCTIONS 1.The appliance should be transported only in an upright position. The packing as supplied must be intact during transportation. 2.If during the course of transport the appliance has to be transported horizontally, it must only be laid on its left hand side when standing in the front of the appliance. After bringing it to upright position,it must not be operated for at least 4 hours to allow the system to settle. 3.Failure to comply with the above instructions could result in damage to the appliance, for which the manufacturer will not be held liable. 4.The appliance must be protected against rain, moisture and other atmospheric influences. 5. When positioning your appliance take care not to damage your flooring, pipes, wall coverings etc. Do not move the appliance by pulling by the door or handle. 6. Empty any water in the drain tray before moving. See section „Defrosting” and „Care & cleaning” for further information. 7. Make sure that the defrost water pipe at the back of the product is fixed to the plastic evaporating pan on the top of the compressor, to avoid defrost water spillage on the floor. Important! . Care must be taken while cleaning/carrying the appliance not to touch the bottom of the condenser metal wires at the back of the appliance, as this could cause injury to fingers and hands. . Do not attempt to sit or stand on top of your appliance as it is not designed for such use. You could injure yourself or damage the appliance. . Make sure that the mains cable is not caught under the appliance during and after moving, as this could damage the cable. . Do not allow children to play with the appliance or tamper with the controls. BEKO plc declines to accept any liability should the instructions not be followed. AETCS – Advanced Electronic Temperature Control System Your Fridge Freezer is equipped with AETCS, the latest innovation from Beko Engineers, which features the following benefits; . Accurate and consistent temperature maintenance for improved performance thanks to advanced electronics used in the control system. . The system in the electronics monitors the ambient temperature and controls the compressor to make sure that the freezer will work in ambient temperatures down to -15°C. This means you can install your appliance, if required, in a garage or similar outside locations where there is no heating. Because the fridge would be too cold, food may be affected, such as salad and fruit. So make sure you don't leave such food in the fridge in very cold ambient conditions. . Because in cold conditions, the appliance works less, it would also save on electricity costs. INSTALLATION INSTRUCTIONS 1. The space in the room where the appliance is installed must not be smaller than 10 cubic metres. 2. Do not place the appliance near cookers, radiators or in direct sunlight as this will cause your appliance to work harder. If installed next to a source of heat or freezer, maintain the following minimum side clearances: From Cookers 2" (50 mm) From Radiators 12" (300 mm) From Refrigerators or Larder Fridge 1" (25 mm) 4 4. Make sure that sufficient room is provided around the appliance to ensure free air circulation. Fit the two plastic wall spacer supplied with the appliance rotating 1/4 turn to the condenser at the back of the refrigerator (see diagram). 5. The fridge/freezer should be located on a smooth surface. The two front feet can be adjusted as required. To ensure that, your appliance is standing upright adjust the two front feet by turning clockwise or anti-clockwise, until the product is in firm contact with the floor. Correct adjustment of feet avoids excessive vibration and noise. 6. Refer to cleaning and care section to prepare your appliance for use. WARNING! Do not connect your appliance to the electricity supply until all the packing and transit protectors have been removed including polystyrene block(s) inserted between the compressor motor and the cabinet (see diagrams). Do not remove the plastic drain tray fitted above the compressor motor on models with auto - defrost fridge. CONDENSERSPACERSCOMPRESSOR 5 ...