Войти:
Оценок - 2, средний балл: 5 ( )

Инструкция по эксплуатации Beko, модель CDA543F

Производитель: Beko
Размер: 268.74 kb
Название файла: 55004cb0-cf08-4e43-b779-2dfdf76f5ec7.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


2. Do not put your fridge freezer in to go below +5 degrees C (41 in winter. This fridge freezer has between +5 and +appliance is installed annex/ shed/garage compartment to run and as frozen food 4 may be 3. Do not place the appliance near cookers, radiators or in direct sunlight as thisGETTING TO KNOW YOUR COMBI BEKO FRIDGE / FREEZER will cause your appliance to work harder. If installed next to a source of heat or freezer, maintain the following minimum side clearances: From Cookers 50 mm (2") From Radiators 300 mm (12") From Freezers 25 mm (1") 4. Make sure that sufficient room is provided around the appliance to ensure free air circulation. Fit the Two plastic wall spacers supplied with the appliance rotating 1/4 turn to the condenser at the back of the appliance (See Diagram). 5. The fridge/freezer should be located on a smooth surface. The two front feet can be adjusted as required. To ensure that your appliance is standing upright adjust the two front feet by turning clockwise or anti-clockwise, until the product is in firm contact with the floor. Correct adjustment of feet avoids excessive vibration and noise. 6. Refer to cleaning and care section to prepare A special receptacle is supplied to store The receptacle is fixed at the back of cabinet, on the side of the compressor. (See diagram) Gently remove the from the receptacle. Never pull mains cord, you may damage appliance. In the case of FEET ensure you locate the provided to avoid FREEZER FAN EGG TRAY SALAD CRISPER ADJUSTABLE DEFROST WATER COLLECTION CHANNEL ICE BANK FROZEN FOOD STORAGE DRAWERS INTERIOR LIGHT BUTTON CABINET SHELVES THERMOSTAT KNOB INTERIOR LIGHT FAST FREEZE COMPARTMENT 5 6 REVERSING THE DOORS (item 7) (item 10) (item 15) We recommend that you reverse doors before switching on for the first time. Tools required: Small and medium size flat and cross-headed screwdrivers, a pair of pliers. Spare Parts supplied in the plastic bag: The following parts, which are exclusively for left hand side fitted hinge operation are supplied in a plastic bag with the appliance: - Upper door top trim hinge cover. - Upper door middle hinge bushing/door stopper assembly. - Hinge pin bushings, 2 different parts supplied as spares for future use. - Hinge pin hole blanking plug, 1 piece supplied as spare for future use. We suggest you keep all the parts supplied in the plastic bag and also parts, which have been removed when reversing doors, in a safe place for possible future, re-use. IMPORTANT: We suggest you ask somebody to help you when moving the appliance around and to hold doors when removing / re-fitting hinges and doors to avoid any injury and damage to the product. Please refer to diagrams supplied. To follow numbers in brackets below, refer to the main diagram. 1. Switch off the appliance at the socket outlet and pull out the mains plug. 2. Remove all loose items and fittings and food, if any, from inside the appliance and door racks. 3. Gently prise off plastic hinge cover of upper door top trim and hinge covers on both sides of front top panel using a small flat-headed screwdriver. (1) 4. Gently tilt the appliance back against a strong wall on its rear side sufficiently to allow the lower hinge to be removed. Take care to protect the appliance, your wall and floor coverings. You can utilise the original packaging to do this. Once you tilt the appliance back, check to make sure the appliance is completely stable and safe before you carry on. (2) 5. Unscrew and remove the lower hinge using a cross-headed screwdriver while holding the lower door firmly. (3) 6. Remove lower door carefully off the middle hinge and stand door upright in a safe place. (4) 7. Open upper door and unscrew and remove the middle hinge while holding the upper door firmly. Use a flat-headed screwdriver. Middle hinge will need to be rotated 180 degrees before re-fitting on the opposite side. (5) 8. Remove upper door carefully off the upper hinge and stand door upright in a safe place. (6) 9. Unscrew and remove the upper hinge using a flat-headed screwdriver. (7) 10. Rotate the upper hinge 180 degrees and then unscrew and remove the hinge pin using a pair opposite side of hinge. (8) 11. Reposition plugs and hinge pin bushings on top of doors on the opposite side of both doors. headed screwdrivers to remove plugs and bushings. Take care not to mark doors. (9) 12. Reposition left hand side feet on the opposite side. (10) 13. Unscrew and remove the bottom door hinge pin bushing/door stopper using a screwdriver. (11) Unscrew and remove the upper door middle hinge pin bushing/door stopper screwdriver. Important: This part cannot be used on the opposite side; left hand side middle hinge pin bushing/door stopper part is supplied in the plastic bag. (11) 14. Re-fit the upper hinge on the left hand side using flat-headed screwdriver. (12) 15. Fit upper door left hand side middle hinge pin bushing/door stopper cross-headed screwdriver. (13) 16. Reposition three small plastic plugs ...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории