Оценок - 1, средний балл: 3 ( )

Производитель: Amana Размер: 906.3 kb Название файла: 344536EN.pdf Язык инструкции:

16 16 What to do if… The absence of frost is due to the continuous circulation of cold air inside the compartment, driven by an automatically controlled fan. Periods of non-operation When the appliance is not in use for long periods, take the following precautions: • disconnect the appliance from electricity supply • remove all food • defrost (if foreseen) and clean the appliance and all accessories • leave the door/doors ajar to prevent unpleasant smells. If the cabinet will be kept on, ask somebody to check it once in a while to prevent the food inside from spoiling in case of a power failure. WHAT TO DO IF… WARNING! Before troubleshooting, disconnect the mains plug from the mains socket. Only a qualified electrician or competent person must do the troubleshooting that is not in this manual. The appliance is noisy The appliance is not supported Check if the appliance stands staproperly ble (all the four feet should be on the floor) The appliance does not The appliance is switched off. Switch on the appliance. operate. The lamp does not operate. The mains plug is not connected Connect the mains plug to the to the mains socket correctly. mains socket correctly. The appliance has no power. Connect a different electrical ap- There is no voltage in the mains pliance to the mains socket. socket. Contact a qualified electrician. The lamp does not work. The lamp is in stand-by. Close and open the door. The lamp is defective. Refer to "Replacing the lamp". The buzzer sounds. The The temperature in the freezer is Refer to "High Temperature Alarm light flashing. too high. Alarm". The compressor operates The temperature is not set cor-Set a higher temperature. continually. rectly. The door is not closed correctly. Refer to "Closing the door". The door has been opened too Do not keep the door open longer frequently. than necessary. The product temperature is too Let the product temperature de- high. crease to room temperature before storage. Problem Possible cause Solution What to do if… 17 Problem Possible cause Solution The room temperature is too high. Decrease the room temperature. The compressor does not start immediately after pressing the FROSTMATIC or COOLMATIC button, or after changing the temperature. This is normal, no error has occurred. The compressor starts after a period of time. Water flows on the rear plate of the refrigerator. During the automatic defrosting process, frost defrosts on the rear plate. This is correct. Water flows into the refrigerator. The water outlet is clogged. Clean the water outlet. Products prevent that water flows into the water collector. Make sure that products do not touch the rear plate. The temperature in the appliance is too low/high. The temperature regulator is not set correctly. Set a higher/lower temperature. The door is not closed correctly. Refer to "Closing the door". The product temperature is too high. Let the product temperature decrease to room temperature before storage. Many products are stored at the same time. Store less products at the same time. The temperature in the refrigerator is too high. There is no cold air circulation in the appliance. Make sure that there is cold air circulation in the appliance. The temperature in the freezer is too high. Products are too near to each other. Store products so that there is cold air circulation. There is too much frost. Food is not wrapped correctly. Wrap the food correctly. The door is not closed correctly. Refer to "Closing the door". The temperature regulator is not set correctly. Set a higher temperature. Upper or lower square is shown in the temperature Display. An error has occurred in measuring the temperature. Call your service representative (the cooling system will continue to keep food products cold, but temperature adjustment will not be possible). dEMo appears on the Display. The appliance is in demonstration mode (dEMo). Keep pressed approximately 10 sec. the OK button since a long sound of buzzer is heard and the Display shut off for a short while: appliance start works regularly. 18 18 Technical data Replacing the lamp CAUTION! Disconnect the plug from the mains socket. 1. Press on the rear hook and at the same time slide the cover in the direction of the arrow. 2. Replace the lamp with one of the same power and specifically designed for household appliances. (the maximum power is shown on the light bulb cover). 3. Fix the lamp cover into its original position. 4. Connect the plug to the mains socket. 5. Open the door. Make sure that the light comes on. Closing the door 1. Clean the door gaskets. 2. If necessary, adjust the door. Refer to "Installation". 3. If necessary, replace the defective door gaskets. Contact the Service Center. TECHNICAL DATA Dimension of the recess Height 1780 mm Width 560 mm Depth 560 mm Rising Time 25 h Voltage 230-240 V Frequency 50 Hz The technical information are situated in the rating plate on the internal left side of the appliance and in the energy label. INSTALLATI...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: