Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Important: Renewing the fleece filter at appropriate intervals prevents the possibility of it catching fire as a result of a build-up of heat, such as occurs when deep-fat frying or roasting is taking place. Renewing the fleece filter: . Under normal operating conditions (1 to 2 hours per day), the fleece filter will require replacing after 8 to 10 weeks. Printed fleece filters must be renewed no later than when the coloured printing has started to fade. . Use only original replacement filters. In so doing you will ensure that safety regulations are upheld and the extractor hood performs as effectively as possible. Disposing of the old fleece grease filter: Fleece grease filters do not contain any pollutants. They can be composted and disposed of as biodegradable waste. 5 Filters and maintenance 2. Press the retaining spring and remove the filter frame. 3. Remove the wire grille and replace the filter mat. 4. Install the filter frame in reverse sequence. Re-attach the retaining spring. The left and right sides of the filter frame must lock into position! Metal grease filter The filter mat is made of non-combustible metal. Caution: As it becomes more and more saturated with grease, the filter also becomes increasingly inflammable. The efficiency of the extractor hood can also be adversely affected. Important: Clean the metal grease filter at regular intervals. Cleaning the metal filter: Under normal operating conditions (1 to 2 hours per day), the metal grease filter will require cleaning after 8 to 10 weeks. . The filter can be cleaned in a dishwasher. This can however cause slight discoloration. Important: Metal filters that are heavily saturated with grease should not be cleaned at the same time as any crockery, etc. . If the filter mat is going to be cleaned by hand, soak it first of all in a hot detergent solution for several hours. Clean the filter with a brush, rinse it off thoroughly and allow it to drip dry. . Use only original replacement filters. In so doing you will be ensuring that the extractor hood performs as effectively as possible. Removing and installing the grease filter Extractor hoods with a filter mat: 1. Rotate the handles on the left and right of the filter grille. 6 Filters and maintenance Extractor hoods with two filter cartridges: Warning: The halogen bulbs must be switched off and cool. 1. Depress the detent on the grease filters in the direction of the arrow and fold down the grease filter slightly. Detach the grease filter by pulling it towards yourself. 2. Clean the grease filters. 3. Re-insert the clean grease filters. Removing and installing the activated carbon filter Extractor hoods with a filter mat: 1. Remove the filter; see grease filter. . The wire grille is no longer required when an activated carbon filter is installed. 2. Place the activated carbon filter on the filter mat and clamp it in. 3. Install the filter frame. . See grease filter. Activated carbon filter 7 Activated carbon filter 5. Insert the activated carbon filter at the rear, fold up and lock in the middle with the wing nut. If the spacer rail has been removed, it must be re-installed. 6. Re-insert the two filter cartridges. Removing the activated carbon filter: . The activated carbon filter is removed in reverse sequence. Changing the activated carbon filter: If used normally (1 to 2 hours daily), the activated carbon filter should be changed approx. once a year. Activated carbon filters can be purchased from SPECIALIST OUTLETS (see optional accessories on the last page). Use original filters only. This will ensure optimum performance. Disposing of the old activated carbon filter: Activated carbon filters do not contain any pollutants. They can be disposed of e.g. as residual waste. Extractor hoods with two filter cartridges: 1. Remove the filter cartridge. . See grease filter. 2. Insert the screw through the wing nut and the sleeve and screw in the middle screw in the false bottom (required only during the initial installation). Screw, sleeve and wing nut are enclosed with the activated carbon filter. 3. Using a screwdriver, press in the two lugs on the false bottom. If a spacer rail has been installed, it must be removed. 4. Tape over the activated carbon filter with the enclosed sealing strip. Cleaning and care Switch off the extractor hood and isolate by pulling out the mains plug or switching off the disconnector on the installation side. . At the same time as you renew the grease filter (see Filters and maintenance), clean off any grease from all accessible parts of the housing. This significantly reduces the fire hazard and ensures that the extractor hood performs as effectively as possible. . Clean the extractor hood with a hot detergent solution or a mild window cleaning agent. . If the hood is extremely dirty (older stains), use a liquid window cleaner. . Do not scratch off dried-on dirt, but wipe off with a damp cloth. . Do not use scouring agents. Warning: Clean the control buttons with a m...