Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
The flaming of foods beneath the hooditself is severely prohibited. The use of exposed flames isdetrimental to the filters and may cause a fire risk, and must therefore be avoided in all circumstances. Any frying must be done with care in order to make sure that the oil does not overheat and burst into flames. As regards the technical and safetymeasures to be adopted for fume discharging it is important to closely follow the relations provided by the competent authorities. The hood must be regularly cleaned onboth the inside and outside (AT LEAST ONCE A MONTH, it is in any event necessary to proceed in accordance with the maintenance instructions provided in this manual).. Failure to follow the instructions as concerns hood and filter cleaning will lead to the risk of fires. Do not use or leave the hood without the lamp correctly mounted because of the possible risk of electric shocks. We decline any responsibility for anyproblems, damage or fires caused to the appliance as the result of the nonobservance of the instructions included in this manual. Operating procedure To deactivate the function before time is The most effective up press T2 button, the hood sets to method of removing . speed 3. vapours produced during cooking is to: T4 Speed timing . Switch the ventilator ON as soon as you begin cooking. . Switch the ventilator OFF a few minutes after you have finished cooking. T1.Lights ON/OFF T2.Speed decrease Speed timing is activated by pressing T4 button, when timing is up the hood switches off. . Timing is divided as follows: Speed 1 - 20 minutes (LED 1 flashing) Speed 2 - 15 minutes (LED 2 flashing) Speed 3 - 10 minutes (LED 3 flashing) Speed 4 - 5 minutes (LED 4 flashing) During timed operation press T2 button and the hood quits the timed mode and decreases the speed. Press T3 button and the hood quits the timed mode and increases the speed. Press T4 button and the hood quits the timed mode maintaining the set speed. Press “T2” button to decrease the speed from 4 (intensive) to 1. Press “T2” button during operation at speed 1, the hood sets to OFF. T3 Speed increase Press T3 button and the hood sets from OFF to speed 1. Press the button (hood ON) to increase the speed of the motor from 1 to 4 (intensive). The respective LED goes on for each speed. Speed 1 LED 1 Speed 2 LED 2 Speed 3 LED 3 Intensive speed LED 4 (flashing) The intensive speed is timed. Standard timing is 5’, at the end of which the hood sets to speed 2. Grease filter signal After 40 hours of operation LED 1 flashes. When such signal appears the grease filter installed needs to be washed. To reset the signal, keep T4 button pressed for 5”. The hood gives out a “BEEP” and LED 1 stops flashing. Charcoal filter signal After 160 hours of operation LED 2 flashes. When such signal appears the charcoal filter installed must be replaced. To reset the signal, keep T4 button pressed for 5”. The hood gives out a “BEEP” and LED 2 stops flashing. In case of contemporaneous signalling of both filters, LEDs 1 and 2 flash alternatively. To reset, carry out the procedure described above for 2 times. The first time it resets the charcoal filter signal, the second time it resets the grease filter signal. The charcoal filter signal is not active in the standard mode. In case the hood is used in filter version it is necessary to enable the charcoal filter signal. Activating charcoal filter signal: Set the hood to OFF and press T4 button for 5”. Once the button has been pressed, the LEDs related to the filter signals currently active light up. The hood gives out a “BEEP” and LED 2 flashes for 2". LEDs 1 and 2 remain on for about 2" before the hood goes back to OFF. Deactivating charcoal filter signal: Set the hood to OFF and press T4 button for 5”. Once the button has been pressed, the LEDs related to the filter signals currently active light up. The hood gives out a “BEEP” and LED 2 switches off. LED 1 remain on for about 2" before the hood goes back to OFF. Filters and maintenance ATTENTION! Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse. Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket. Maintenance of the panel Dismantling: Extract with decision (LOWER SIDE) and rotate upwards. Cleaning: The panel must be cleaned as often as the grease filter, wash by hand with nonabrasive d...
Эта инструкция также подходит к моделям:Вытяжки - 3BC8890B/01 (226.2 kb)
Вытяжки - 3BC8890B/03 (226.2 kb)