Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
If long, rough exhaust-air pipes, many pipe bends or smaller pipe diameters are used, the air extraction rate will no longer be at an optimum level and there will be an increase in noise. The manufacturer of the extractor hoods accepts no liability for complaints which can be attributed to the design and layout of the pipework. If pipes have different diameters: Insert sealing strip. For exhaust-air mode, ensure that there is an adequate supply of fresh air. Round pipes Internal diameter Flat ducts Cross-section l 100 mm 179 cm2 l 120 mm 113 cm2 l 150 mm 177 cm2 Air connector l 150 mm Mount the pipe directly onto the air outlet on the hood. Attach the reducing connector (enclosed or available from specialist retailer) to the air pipe and then attach to the exhaust-air duct. Air connector l 120 mm Mount the pipe directly onto the air outlet on the hood. Attach the reducing connector (enclosed or available from specialist retailer) to the air pipe and then attach to the exhaust-air duct. Snap the one-way flap into the air pipe. The two lightly sprung flaps must be able to move upwards. Circulating-air mode With activated carbon filter if exhaust-air mode is not possible. The complete installation set can be obtained from specialist outlets. The corresponding accessory numbers can be found at the end of these operating instructions. Preparing the wall The wall must be flat and perpendicular. Make sure that the wall can bear the applied loads. The provided screws and wall plugs are suitable for solid masonry. On all other wall types (e.g. plasterboard, porous concrete, Poroton bricks) use the appropriate fasteners. Ensure that the wall is capable of providing a firm hold for mounting screws and plugs. Weight in kg: We reserve the right to construction changes within the context of technical development. Exhaust air Recirculating air 060 cm 12,5 13,5 070 cm 13,0 14,0 090 cm 13,9 14,9 100 cm 14,8 15,8 120 cm 16,0 17,5 15 Electrical connection WARNING: THIS APPLIANCE MUST BE EARTHED IMPORTANT: Fitting a Different Plug: The wires in the mains lead are coloured in accordance with the following code: Green and Yellow – Earth Blue – Neutral Brown – Live If you fit your own plug, the colours of these wires may not correspond with the identifying marks on the plug terminals. This is what you have to do: 1.Connect the green and yellow (Earth) wire to the terminal in the plug marked ‘E’ or with the symbol ( ), or coloured green or green and yellow. 2. Connect the blue (Neutral) wire to the terminal in the plug marked ‘N’ or coloured black. 3.Connect the brown (Live) wire to the terminal marked ‘L’, or coloured red. The extractor hood should only be connected to an earthed socket that has been installed according to relevant regulations. If possible, site the earthed socket directly behind the chimney panelling. The earthed socket should be connected via its own circuit. If the earthed socket is no longer accessible following installation of the extractor hood, ensure that there is a permanently installed disconnector. If it is necessary to wire the extractor hood directly into the mains: The extractor hood should only be connected to the electricity supply by a properly qualified electrician. A separator must be installed in the household circuit. A suitable separator is a switch that has a contact gap of more than 3 mm and interrupts all poles. Such devices include circuit breakers and contactors. If the connecting cable for this appliance is damaged, the cable must be replaced by the manufacturer or his customer service or a similarly qualified person in order to prevent serious injury to the user. Electrical data: Are to be found on the name plate inside the appliance after removal of the filter frame. Before undertaking any repairs, always disconnect the extractor hood from the electricity supply. Length of the connecting cable: 1.30 m. This extractor hood corresponds to EC regulations concerning RF interference suppression. Installation This extractor hood is intended to be mounted onto the kitchen wall. 1. Remove the grease filter (refer to Operating Instructions). 2. Draw a line on the wall from the ceiling to the lower edge of the hood at the centre of the location where the hood is going to be mounted. 3. Using the template, mark positions on the wall for the screws. Ensure that the minimum distance between the hob and the extractor hood is maintained – 550 mm for an electric hob and 650 mm for a gas hob. The bottom edge of the template equates to the lower edge of the extractor hood. 4. Drill 5 holes (dia. 8 mm) for the extractor hood and 4 holes (dia. 8 mm) for the brackets for fixing the flue ducts and insert wall plugs flush with the wall. Note: Take into account any special accessories that are going to be fitted. 5. Screw on the 2 brackets for fixing the upper and lower flue ducts. 6. In order to help fix the hood onto the wall, screw in the middle screw (without a washer) until it protrudes by ap...
Эта инструкция также подходит к моделям:Вытяжки - VVA62E150/02 (2.29 mb)
Вытяжки - VVA92E150/01 (2.29 mb)
Вытяжки - VVA92E150/02 (2.29 mb)