Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Fan Speed Pressing the button once, from an off state, turns the ventilator on low. Each successive press of the button increases the fan speed until high speed is reached then the fan cycles back to the low speed. • The LEDs above this button indicate the current fan speed. When the fan is on, the corresponding LED is illuminated. 1 — Low 2 — Medium 3 — High Delay Shut Off • Press Delay button to turn fan on high for 10 minutes. If the ventilator is off when the Delay button is pressed, the ventilator will turn on to the high speed setting for 10 minutes. At the end of the cycle the ventilator will turn off. If the ventilator is on when the Delay button is pressed, the ventilator runs for 10 minutes at the current speed then turns off. • During a timed period, the LED above the Delay button is illuminated. • To interrupt a timed period, press Fan Speed or Off button. Clean Filter Reminder After 40 hours of operation, the clean filter reminder LED above this button will illuminate indicating that the filters need to be cleaned. When this indicator illuminates, clean the filters as instructed on page 5. After cleaning, press this button for 3 seconds to reset the 40-hour period and turn the LED off. Light On/Dim/Off This button controls the halogen lighting. The first press turns the lights on. A second press dims the lights. A third press turns the lights off. English 4 Heat Lamp (some models) The buttons marked “L” and “R” independently control the left and right infrared heating lamps, turning the lights on or off. Heat Sensor Note: The heat sensor features listed below are not available when the hood is installed with the remote control accessory. Oven Temperature Condition The high temperature sensor protects the hood from high temperatures which may damage components. The control is set to activate at 161° F (72° C) and reset at 140°F (60° C). When activated, the ventilator will turn on low and the corresponding LED will blink, indicating an oven temperature condition. While the high temperature sensor is activated, the blower speed can be changed or turned off. If the blower is turned off, the corresponding LED will blink. Light controls will remain operational. When the control sensor reaches 140°F (60° C), a reset will occur. During reset, the control will revert back to the operational state prior to the high temperature condition. High Temperature Fault Condition The circuit is equipped with an alarm indicating that the heat sensor protection is not working due to a damaged sensor. In the case of this extreme condition, the three speed indicator LEDs will start blinking. All the controls will be operational except for the speed indicators. Care and Cleaning WARNING: Be sure the entire appliance (including the grease filters and light bulbs) has cooled and grease has solidified before attempting to clean any part of the appliance. To Clean Hood Surface • For general care, wipe the outside of the stainless steel with sudsy water or household cleaners such as Fantastik® or Formula 409®, rinse well and dry with a clean soft cloth to avoid water marks. • Wipe and dry stainless steel in the same direction as the grain. Avoid using too much pressure, which may mar the surface. • Do not use abrasive products such as steel wool. • To remove finger prints and give added shine, use a stainless steel cleaner such as Stainless Steel Magic® , Hadco Stainless Steel Polish, Sprayway® Stainless Steel Polish and Cleaner, or 3M Stainless Steel Cleaner and Polish. • Do not allow any cleaning compounds to remain in contact with stainless steel for extended periods. The use of brand names is intended only to indicate a type of cleaner. This does not constitute an endorsement. The omission of any brand name cleaner does not imply its adequacy or inadequacy. Many products are regional in distribution and can be found in the local markets. It is imperative that all products be used in strict accordance with instructions on the package. To Clean Filters and Troughs Your hood has removable aluminum or stainless steel filters, stainless steel grease troughs and stainless steel side panels. They must be cleaned when the filter light illuminates on the control panel or whenever they collect grease. When used over a grill, wok or other high grease applications, more frequent cleaning may be required. To Remove Filters and Grease Troughs: • Turn the fan and lights off. Be sure filters are cool and grease has congealed before removal. • Remove in the following order: 1) Filters — Start with center filters, push up, then pull out from the bottom. 2) Side Panels — Remove these the same way as the filters. 3) Grease Troughs — lift up and out. • The filters and grease troughs can be washed by hand or in the dishwasher. The front and side panels may be washed with warm soapy water and polished with stainless steel cleaner. English 5 Reverse the above directions to reinsert the trough, filters and side panels. Note: Do not use cooktop ...
Эта инструкция также подходит к моделям:Вытяжки - PH36CS/02 (820.1 kb)
Вытяжки - PH42CS/02 (820.1 kb)
Вытяжки - PH48CS/02 (820.1 kb)
Вытяжки - PH54CS/02 (820.1 kb)