Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Light controls will remain operational. When the control sensor reaches 140°F (60° C), a reset will occur. During reset, the control will revert back to the operational state prior to the high temperature condition. High Temperature Fault Condition - The circuit is equipped with an alarm indicating that the heat sensor protection is not working due to a damaged sensor. In the case of this extreme condition, the three speed indicator LEDs will start blinking. All the controls will be operational except for the speed indicators. 3 CARE AND CLEANING • The filters and grease troughs can be washed by To Clean Hood Surface hand or in the dishwasher. The front and side • For general care, wipe the outside of the stainless steel with sudsy water or household cleaners such as Fantastic® or Formula 409®, rinse well and dry with a clean soft cloth to avoid water marks. • Wipe and dry stainless steel in the same direction as the grain. Avoid using too much pressure, which may mar the surface. • Do not use abrasive products such as steel wool. • To remove finger prints and give added shine, use a stainless steel cleaner such as Stainless Steel Magic®, Hadco Stainless Steel Polish, Sprayway® Stainless Steel Polish and Cleaner, or 3M Stainless Steel Cleaner and Polish. • Do not allow any cleaning compounds to remain in contact with stainless steel for extended periods. The use of brand names is intended only to indicate a type of cleaner. This does not constitute an endorsement. The omission of any brand name cleaner does not imply its adequacy or inadequacy. Many products are regional in distribution and can be found in the local markets. It is imperative that all products be used in strict accordance with instructions on the package. To Clean Filters and Troughs Your hood has removable aluminum filters, stainless steel grease troughs and stainless steel side panels. They must be cleaned when the filter light illuminates on the control panel or whenever they collect grease. When used over a grill, wok or other high grease applications, more frequent cleaning may be required. To Remove Filters and Grease Troughs: • Turn the fan and lights off. Be sure filters are cool and grease has congealed before removal. • Remove in the following order: 1. Filters -Start with center filters, push up, then pull out from the bottom. 2. Side Panels - Remove these the same way as the filters. 3. Grease Troughs - lift up and out. panels may be washed with warm soapy water and polished with stainless steel cleaner. Reverse the above directions to reinsert the trough, filters and side panels. ® OFF FAN SPEED DELAYAA SHUT OFF FILTERILIL LIGHT HEAT LAMPSAA L R1 2 3 Figure 2 Note: Do not use cooktop while hood is disassembled. Grease troughs must be in place before installing the aluminum filters. Figure 3 Side Panel Grease Trough Side PanelFilters ® Filters 2 1 2 1 Note: Depending upon the size and model of hood, there will be anywhere from 1 to 3 filters per hood. 4 MAINTENANCE Lights NOTE: Turn off the lights and fan. Allow the lights to cool before handling. If new lights do not operate, be sure lights are inserted correctly before calling for service. Halogen Light Replacement • Using a flat edge from a screwdriver or equivalent tool, pry loose the lens cover as shown in Figure 4. • Remove the damaged light and replace with a new 12 Volt, 20 Watt (maximum) halogen light made for a G-4 base. Follow package directions and do not touch new light with bare hands. • Reinstall the light and cover. Figure 4 Heat Lamp Replacement • Turn heat lamp counterclockwise to remove. • Replace lamp with either a PAR-38 175W heat lamp or a PAR-40 250W heat lamp. The PAR-38 175W heat lamp provides a tighter seal within the enclosure and produces the same amount of effective heat with lower energy consumption. These lamps may not be readily available at local retail outlets. The PAR-40 250W heat lamp is more widely available. It can be used instead. PAR-38 175W heat lamps can be purchased through the following r...
Эта инструкция также подходит к моделям:Вытяжки - PH36CS/01 (230.63 kb)
Вытяжки - PH42CS/01 (230.63 kb)
Вытяжки - PH48CS/01 (230.63 kb)
Вытяжки - PH54CS/01 (230.63 kb)