Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
435 mm. If the cupboard is deeper than 293 mm, the extractor hood can be moved back, e.g. to put a spice rack in front of the extractor hood. To do this, place the template OII further back. Ensure that the cupboard is stable both during and after installation, even if fitted at the end of a row of kitchen units. Do not install the extractor hood at the end of the kitchen line. 25 26 3. Tighten the two fixing screws with a screwdriver (cordless). 5. If required, shorten the wall cover to the required dimension (e.g. saw off). Attach the wall cover with the enclosed clips. Screw the wall cover to the wall cupboard. 6. Feed the mains connection cable out of the cupboard. 7. Connect the pipes in the wall cupboard. – If required, attach the air hose to the cupboard ceiling –. 8. Re-insert grease filter (see Operating instructions). Fitting into wall cupboard Check door alignment and readjust if necessary. 1. Remove grease filter (see Operating instructions). 2. Lift the extractor hood into the cupboard from below until both fixing lugs have locked firmly into position. . Align the extractor hood in the cupboard. . Carefully tighten both fastening screws. 4. Also attach the extractor hood to the left and right wall cupboards with 2 screws each side. 27 Fitting into wall cupboard Note: The extractor hood housing can be clad inside the wall cupboard (e.g. with chipboard). If so, observe the following: . The intermediate base must not be placed on the extractor hood housing. . Never attach cladding to the housing. . Provide access for customer service. . If the extractor hood is to be installed further back in the cupboard, the stops for the filter drawer can be moved forwards. . To do this, undo the screws, move the stops and retighten the screws. 2. Align handle moulding and screw to the appliance. Exhaust air Circulating air 13,5 14,0 We reserve the right to construction changes within the context of technical development. Weight in kg: Attaching the handle moulding: A handle moulding must be attached to the filter drawer. This handle moulding may be a wooden strip which matches the kitchen units or a handle moulding available as an optional accessory (see optional accessories on the back page). 1. Using the enclosed template OIII , mark the attachment points on the wooden strip and make holes with a bradawl. When you drill: 2 mm dia – max. 10 mm in depth. Electrical connection WARNING: THIS APPLIANCE MUST BE EARTHED IMPORTANT: Fitting a Different Plug: The wires in the power cord are colour coded as follows: Green and Yellow – Earth Blue – Neutral Brown – Live If you fit your own plug, the colours of these wires may not correspond with the identifying marks on the plug terminals. Proceed as follows: 1. Connect the green and yellow (Earth) wire to the terminal in the plug marked ‘E’ or with the symbol ( ), or coloured green or green and yellow. 2. Connect the blue (Neutral) wire to the terminal in the plug marked ‘N’ or coloured black. 3. Connect the brown (Live) wire to the terminal marked ‘L’, or coloured red. The extractor hood may be connected to a correctly installed earthed socket only. Attach the earthed socket near the extractor hood in an accessible position. . The earthed socket should be connected via its own power circuit. If appliances do not feature the OFF delay function, the indicator may start flashing when the extractor hood has been switched off for several hours via a separate switch, even though the grease filters are not yet saturated. (See instructions for use, section on filter and maintenance). Electrical specifications: These can be found on the rating plate inside the appliance following removal of the filter frames. Before carrying out repairs, always isolate the appliance. Length of the connection cable: 1.30 m. If permanent connection is required: The extractor hood may only be connected by an electrician registered with the local electricity board. A disconnecting device must be provided on the installation side. Switches with a contact opening of more than 3 mm and all-pole disconnection are regarded as disconnecting devices. These include LS switches and contactors. This extractor hood complies with EU regulations on interference suppression. Removal from the wall cupboard 1. Disconnect from power. 2. Disconnect pipes. 3. Remove filters. 4. Undo right and left fixing screws until the extractor hood cannot drop any further. Do not lift the extractor hood when undoing the fixing screws. 5. Raise the extractor hood briefly until the fixing lugs detach and the appliance can be lowered. Fastening screws may project. When raising the extractor hood, do not force in the filter drawer. 6. Preparing for re-installation: Screw in the left and right fixing screws until the lugs are pressed out at the sides. Mode d’emploi: Description de l'appareil Commutateur Tiroir-filtre Lumiere/Ventilateur Modes de fonctionnement Air evacue a l'exterieur: . Le ventilateur de la hotte aspire les bu...
Эта инструкция также подходит к моделям:Вытяжки - LI46730/02 (3.94 mb)
Вытяжки - LI46730/03 (3.94 mb)