Войти:
Оценок - 0, средний балл: 0 ( )

Инструкция по эксплуатации Bosch, модель LI44930/01

Производитель: Bosch
Размер: 4.26 mb
Название файла:
Язык инструкции:itenesfrdenlpt
Перейти к скачиванию



Фрагмент инструкции


Align the cupboards exactly. If required, place the side cupboards flush underneath. The side panels must not project over the base of the adjacent unit by more than 0.5 mm. 25 Exhaust air Circulating air 16,0 16,5 We reserve the right to construction changes within the context of technical development. Weight in kg: 26 3. Screw in the adjusting screws by hand until the extractor hood is situated on the base of the cupboard. 7. Feed the mains connection cable out of the cupboard. 8. Connect the pipes in the wall cupboard. – If required, attach the air hose to the cupboard ceiling –. 9. Re-insert grease filter (see Operating instructions). Fitting into wall cupboard Check door alignment and readjust if necessary. 1. Remove grease filter (see Operating instructions). 2. Lift the extractor hood into the cupboard from below until both fixing lugs have locked firmly into position. . Align the extractor hood in the cupboard. . Carefully tighten both fastening screws. 4. Also attach the extractor hood to the left and right wall cupboards with 2 screws each side. First make pilot holes with a bradawl. 5. Seal the holes with 2 stoppers each on the left and right. 6. If required, shorten the wall cover to the required dimension (e.g. saw off). Attach the wall cover with the enclosed clips. Screw the wall cover to the wall cupboard. Re-adjusting the limit switch: 1. Check whether the extractor hood switches off when the filter drawer is inserted. 2. If the extractor hood does not switch off, re-adjust the limit switch. 3. Unscrew the screw in small steps – max. 2 revolutions. Fitting into wall cupboard Note: The extractor hood housing can be clad inside the wall cupboard (e.g. with chipboard). If so, observe the following: . The intermediate base must not be placed on the extractor hood housing. . Never attach cladding to the housing. . Provide access for customer service. . If the extractor hood is to be installed further back in the cupboard, the stops for the filter drawer can be moved forwards. . To do this, undo the screws, move the stops and retighten the screws. Attaching the handle moulding: A handle moulding must be attached to the filter drawer. This handle moulding may be a wooden strip which matches the kitchen units or a handle moulding available as an optional accessory (see optional accessories on the back page). 1. Using the enclosed template OIII , mark the attachment points on the wooden strip and make holes with a bradawl. When you drill: 2 mm dia – max. 10 mm in depth. 2. Align handle moulding and screw to the appliance. 27 Electrical connection WARNING: THIS APPLIANCE MUST BE EARTHED IMPORTANT: Fitting a Different Plug: The wires in the power cord are colour coded as follows: Green and Yellow – Earth Blue – Neutral Brown – Live If you fit your own plug, the colours of these wires may not correspond with the identifying marks on the plug terminals. Proceed as follows: 1. Connect the green and yellow (Earth) wire to the terminal in the...

Эта инструкция также подходит к моделям:
Вытяжки - LI44930/02 (4.26 mb)
Вытяжки - LI44930/03 (4.26 mb)
Вытяжки - LI44930/04 (4.26 mb)
Вытяжки - LI46930/01 (4.26 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории