Войти:
Оценок - 0, средний балл: 0 ( )

Инструкция по эксплуатации Bosch, модель DHI635KAU/01

Производитель: Bosch
Размер: 773.65 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


2. Mark two points – right and left – on the inside of the cupboard where the hood is to be mounted, and start the hole with a gimlet. Details for drilling: l 2 mm – max. 10 mm deep. Attention: . Use enclosed template OII for marking points where hood is to be mounted. . The mounting points shown on the template have been configured in such a way as to allow a 20 mm thick handle to be attached flush with the front edges of the cupboard. . A stop allows the handle (Dimension .) to be positioned further forwards. 21 32 600 170 280-350 mind 300. =0 0 If the cupboard depth is greater than 280 mm, the hood can be mounted further back, . . . if the light strip under the cupboard . . . units is mounted further back, . . . if the handle is more than 20 mm thick. Position the template OII further back. Preparing the wall cupboard 3. Align and screw on the enclosed mounting rails. Note the thickness of the sides of the cupboard (16 mm or 19 mm). dimension X. x=16mm x=19mm X If the interior depth of the cupboard is less than 280 mm, the 250 mm high rear panel must be removed. Installation inside the wall cupboard 1. Remove the filter frames (see Operating Manual). 2. If the hinges are no longer accessible when the extractor hood has been installed, align the cupboard doors. 3. Lift and push the extractor hood from below into the cupboard until the installation aids on the left and right lock into position. 4. Pull out the filter drawer all the way. 5. Attach the extractor hood by screwing in 2 screws on the left and right. Do NOT tighten the screws. Raise the extractor hood. 6. Align the extractor hood in the cupboard and tighten the screws. 15 Installation inside the wall cupboard 7. Feed the mains connection cable through the aperture into the upper cupboard and connect the pipe. 8. Connect to the power supply. 9. If required, shorten the wall cover to the required size (e.g. saw off) and screw to the upper cupboard. Attaching a handle: . A handle must be attached to the filter drawer. . This handle can either be a wooden strip that matches the kitchen cupboards or a the handle that is available as an optional accessory (see section on optional accessories in the user instructions). 1. Mark two points on the handle with the enclosed template OIII and make holes with a bradawl. If the holes are drilled: l 2 mm – max. 10 mm deep. 14,5 598 350 2. Align the handle and screw onto the appliance with the two enclosed screws. 3. Insert the filter frames (see Operating Manual). Note: The extractor hood housing inside the wall cupboard can be boarded up (e.g. with chipboard). Please observe the following: – The shelf must not be rest upon the extractor hood housing. – The board at the front should not be attached to the housing. – Provide access for customer service. Removal: The extractor hood is removed in reverse sequence. Note: In circulating-air mode the activated carbon filter and plastic holder must be removed in order to gain access to the mounting screws...

Эта инструкция также подходит к моделям:
Вытяжки - DHI635KAU/02 (773.65 kb)
Вытяжки - DHI635KAU/03 (773.65 kb)
Вытяжки - DHI635KAU/04 (773.65 kb)
Вытяжки - DHI635KAU/05 (773.65 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории