Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
If the extractor hood is operated in exhaust-air mode at the same time as a flue-type heater (e.g. gas, oil or solid-fuel heater, instantaneous water heater, boiler), ensure that there is an adequate air supply which the heater requires for combustion. Safe operation is possible provided that the partial vacuum in the room in which the heater is installed does not exceed 4 Pa (0.04 mbar). This can be achieved if the combustion air is able to flow through non-lockable openings, e.g. in doors, windows and in conjunction with an air supply/air-intake wall box or by other technical procedures such as reciprocal interlocking. If the air intake is inadequate, there is a risk of poisoning from combustion gases, which are drawn back into the room. An air-intake/exhaust-air wall box by itself is no guarantee that the limiting value will no be exceeded. Note: When assessing the overall requirement, the combined ventilation system for the entire household must be taken into consideration. This rule does not apply to the use of cooking appliances, such as hobs and gas cookers. The extractor hood can be used without restriction in circulating air mode – with an activated carbon filter. For exhaust air mode always cut out the protective grid in the air connector. 120 150 120 150 120 150 12 Before installation With exhaust mode, a backwash valve should be installed unless it is already incorporated in the exhaust pipe or wall box. If a backwash valve is not included with your appliance, your dealer can supply you with one (see accessories). Installation backwash valve: Insert the backwash valve in the mounting openings on the air connector. If the exhaust air is being routed through the outside wall, a telescopic wall box should be used. Connecting to O100 mm exhaustair duct Attach the reducing adapter (enclosed or available from specialist dealer) to the air outlet. Attach the exhaust-air duct to the adapter. Connecting to O120 mm exhaustair duct Attach the exhaust-air duct directly to the air outlet. Connecting to O150 mm exhaustair duct Attach the enlarging adapter (enclosed or available from specialist dealer) to the air outlet. Attach the exhaust-air duct to the adapter. If a backflow flap has been installed, check that it functions properly. Circulating-air mode With activated carbon filter if exhaust-air mode is not possible. The air purified by an additional activated carbon filter is returned to the room. After installing the extractor hood, insert the activated carbon filter. For installing see Filters and maintenance. If the extractor hood is installed beneath a cabinet, ensure that there is an adequate air outlet (min. 177 cm2). The extractor comes as standard equipped with a protective grid in the air connector. If this is has been removed (in the case of exhaust air operation), the air connector must be supplemented by a reducer piece with protective grid (see section on special accessories). Electrical connection WARNING: THIS APPLIANCE MUST BE EARTHED IMPORTANT: Fitting a Different Plug: The wires in the power cord are colourcoded as follows: Green and Yellow – Earth Blue – Neutral Brown – Live If you fit your own plug, the colours of these wires may not correspond with the identifying marks on the plug terminals. Proceed as follows: 1. Connect the green and yellow (Earth) wire to the terminal in the plug marked ‘E’ or with the symbol ( ), or coloured green or green and yellow. 2. Connect the blue (Neutral) wire to the terminal in the plug marked ‘N’ or coloured black. 3. Connect the brown (Live) wire to the terminal marked ‘L’, or coloured red. The extractor hood may be connected to a correctly installed earthed socket only. Attach the earthed socket near the extractor hood in an accessible position. . The earthed socket should be connected via its own power circuit. . If appliances do not feature the OFF delay fu...
Эта инструкция также подходит к моделям:Вытяжки - DHE635BGB/02 (1.97 mb)
Вытяжки - DHE635BGB/03 (1.97 mb)
Вытяжки - DHE645MGB/02 (1.97 mb)
Вытяжки - DHE645MGB/03 (1.97 mb)