Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Operating the extractor hood The most effective method of removing vapours produced during cooking is to: . Switch the ventilator ON as soon as you begin cooking. . Switch the ventilator OFF a few minutes after you have finished cooking. Switching on appliance: Press the Lor + button. . The fan starts at Setting }. Switching on the fan settings/intensive setting: 1. To increase the fan settings or switch on the intensive setting c, press the + button. . The intensive setting operates at maximum power which should be used only briefly. If the intensive setting is not switched off manually, the fan automatically switches back to Setting }after 10 minutes. 2. To switch off the intensive setting c or switch back to fan settings ~ – } – |and switch off the extractor hood completely, press the – button. Fan – off – Fan – on – Fan settings Fan settings – lower – – higher – Intermittent ventilation Light on / off Display:Fan on / off . Fan settings / Intensive setting c . Saturation – grease filter # . Saturation – activated carbon filter a Intermittent ventilation . Used for ventilating the kitchen at hourly intervals at the lowest fan setting, round the clock. Switching on appliance: Press the button and insert the filter drawer. . The fan runs for 5 minutes at Setting |, then switches off for 55 minutes. This process is repeated every hour. Switching off: Press the button. Operating the extractor hood Switching off: There are 2 different ways of switching off the appliance. Switching off directly: Press the Lbutton. Important: All fan functions are switched off. Switching off appliance with fan run-on: Insert filter drawer all the way. The fans operate in the last switched-on stage for around another 10 minutes and then switch off. . If the intensive setting is switched on when the filter drawer is inserted, the intensive setting automatically switches back during run-on. . If intermittent ventilation is switched on, it continues operating normally following run-on. Light . The light can be used at any time, even when the appliance has been switched off. Switching on/off: Press the a button. Adjusting the brightness: . Hold down the a button until the desired brightness is obtained. Special functions Switching on the light automatically, e.g. via a timer: . Fan and light must be switched off. Switching on: Simultaneously press the – and buttons. . After approx. 3 seconds the light switches on to acknowledge the setting. Switching off: Repeat the process with the light switched on. . After approx. 3 seconds the light switches off to acknowledge the setting. 22 Removing and inserting the metal-mesh grease filters: Warning: The halogen bulbs must be switched off and cool. 1. Pull the filter drawer all the way out. 2. Depress both catches at the front of the grease filter and remove the grease filter. 4. Clean the filters. 5. Insert the clean filters back into the hood. 6. Cancel the # display. . Press the L button for at least 3 seconds. The # display then goes out. 3. Depress the catches at the rear of the grease filter and remove the grease filter. Grease filters: Metal-mesh filters are used to trap the grease particles in the cooking vapours. The filter mats are made from noncombustible metal. Caution: As the filter becomes more and more saturated with grease, there is an increased risk of fire and the function of the extractor hood may be impaired. Important: By cleaning the metal grease filters at appropriate intervals, the possibility of them catching fire as a result of a build-up of heat such as occurs when deep-fat frying or roasting is taking place, is reduced. Saturation indicator: When the grease filters reach saturation point, an acoustic signal is sounded for 6 seconds after the fan has switched off, and an # appears in the display. The grease filters should be cleaned straight away. Cleaning the metal-mesh grease filters: . The filters can be cleaned in a dishwasher. However, they may become slightly discoloured. Important: Do not wash highly saturated metalmesh grease filters with other utensils. . If cleaning the filters by hand, soak them in a hot soap solution. Then brush the filters, rinse thoroughly and leave to drain. Filters and maintenance Filters and maintenance Activated carbon filter: For neutralizing odours in recirculating mode. Caution: As the filter becomes more and more saturated with grease, there is an increased risk of fire and the function of the extractor hood may be impaired. Important: Change the activated carbon filter promptly to prevent the risk of fire from the accumulation of heat when deep-fat frying or roasting. Inserting the filter: Warning: The halogen bulbs must be switched off and cool. 1. Remove the metal filters (see "Removing and inserting the metal grease filters"). 2. Insert the activated carbon filter. 3. Engage the catches at both sides. 4. Insert the metal-mesh grease filters (see ”Removing and inserting the metal-mesh grease filters”). 5. Cancel the a disp...
Эта инструкция также подходит к моделям:Вытяжки - AF280160/02 (15.02 mb)
Вытяжки - AF280160/03 (15.02 mb)
Вытяжки - AF280160/04 (15.02 mb)