Then plug it in, turn it on and... breathe. Don't hear anything? Check the blue "power on” light. Blueair is so quiet, you may not realize it's on. But as the pat- ented Blueair system removes dust, pollen, smoke, gases and odors from your indoor environment, we think you'll notice the difference, G E N E R A L S A F E T Y I N S T R U C T I O N S The Blueair300/Blueair400 is an electrical appliance. Before using it for the first time, please read these safety instructions and take precaution

in North America and Blueair AB outside of North America and contains the only express warranty provided to you. BLUEAIR DISCLAIMS ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND ANY IMPLIED WARRANTY, GUARANTEE OR REPRESENTATIONS AS TO THE SUITABILITY FOR ANY PARTICULAR PURPOSE, PERFORMANCE, QUALITY AND ABSENCE OF HIDDEN DEFECTS, AND ANY REMEDY FOR BREACH OF CONTRACT, WHICH BUT FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION, OPERATION OF LAW, CUSTOM OF TRADE OR COURSE OF DEALING, INCLUDING IMPLIED

It's not designed for use outdoors or in wet areas (such as bathrooms). SETTINGS When turning on the Blueair 200 series after the unit has been off, turn the speed control to level 3 for a few minutes of fast initial cleaning. Then adjust to the desired speed: 1. HEPASilent (for nighttime use) 2. Moderate fan speed (for daytime use) 3. Maximum fan speed (for fast initial cleaning or very polluted air) For best results, run your Blueair 200 series 24 hours a day, 7 days a week. Continuous o

TABLE OF CONTENTS Page INTRODUCTION .................................. 1 HOWITWORKS .................................. 1 SAFETYCONSIDERATIONS ........................ 1 APPLICATIONCONSIDERATIONS .................. 2 INSTALLATION ................................. 3- --5 START- --UPANDOPERATION ....................... 6 MAINTENANCE .................................. 6 TROUBLESHOOTING.............................. 7 SPECIFICATIONSANDDIMENSIONS ................ 8 WARRANTY ...........................

Step 3—Confirm that the furnace blower is operating. NOTE: Power will not be supplied to the Infinityt Air Purifier from the furnace controls EAC terminals unless the blower is running. Step 4—Confirm that power provided from the furnace control EAC terminals is being conducted through the wiring to the Infinityt Air Purifier power supply. Step 5—If all of the above steps are completed and the power indicator light is still not illuminating, replace the power supply on the enhancement module. No

ELECTRICAL SHOCK AND HIGH VOLTAGE HAZARD Failure to follow this warning could result in personal injury or death. Before installing or servicing system, always turn off main power to system. There may be more than one (1) disconnect switch. ! WARNING Step 2 —Turn the Infinityt Air Purifier switch to the off position. Step 3 —Remove the Infinityt Air Purifier door. Step 4 —Unplug the power cord and flow sensor cable (if connected) from the enhancement module 9 ( See Fig. 7 and 8) Step 5 —Slide ou

NOTE: Cable connector and block--off plates will need to be removed and re--installed if the power cord is re--routed. Screws on the cable connector clamp should be tightened to 9 in. -- lbs. torque. NOTE: The Infinityt Air Purifier is to be powered by 208/230Vac/60 Hz. NOTE: The Infinityt Air Purifier should only be powered when airflow is present. An airflow sensor is factory--installed (See Fig. 2 and Fig. 11). In order to bypass the airflow sensor, use the special bypass jumper included in t

15 --Dimensions 10 WARRANTY FOR SERVICE OR REPAIR, FOLLOW THESE STEPS IN ORDER: FIRST: Contact the installer. You may find their name on the product or in your Homeowner’s Packet. If the installer’s name is not known, call your builder or home retailer if yours is a new residence. SECOND: Contact the nearest distributor. (See telephone yellow pages.) THIRD: Contact: CARRIER CORPORATION Consumer Relations P.O. Box 4808 Syracuse, New York 13221 Telephone: 1- --800- --CARRIER (227- --7437) 1- --315

In the case of the 020 sized units, each cell should have an even loading pattern. Adjust alignment or replace spring. Replace. Reduce air volume to design cfm. Seal. Insufficient air — check return air grilles for obstruction by furniture, drapes, etc.,and remove, check blower for proper air flow. Replace or reposition as per Maintenance Instructions, Owner's Manual. Install turning vanes or air baffles WA *0 mt mW'm^ m mbs ta tfe »1 Radio or T.V. Interference Accumulation of foreign particles

Refer to Step 7. d. If indicator light does not light, go to Step 5. STEP 5 - PUSH TEST BUTTON a. Energize power supply as in Step 1, a and b. b. Push button. Snapping sound indicates proper high-voltage output from power supply and surge resistor. Failure is probably in cells or top guide assembly or in the light circuit within the power door. Check cells, light and light circuit. If light is faulty, replace switch and light assembly. c. If there is no arcing or snapping, go to Step 6. ST