Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Thread a 5/16-18 flange nut (B) Fig. 3, on a 5/16-18 x 1-1/2" eye bolt (C). 2. Thread the eye-bolt (C) Fig. 3 in the hole (D). NOTE: Tighten the eye-bolts at least eight complete turns. 3. Tighten the flange nut (B) Fig. 3 against the air cleaner. 4. Repeat this process for the remaining hole in the top of the air cleaner (Fig. 4). This tool weighs approximately 40 pounds. Make certain the unit is securely supported when mounting it to a ceiling or overhead support. Never secure the air cleaner hardware to drywall, drop ceiling tile/frame, or other non-structural members. 8 When suspending the air cleaner from the ceiling or other overhead support, use steel s-hooks that are a minimum of 1/4". Thread all lag hooks at least 1-1/2" into supporting structural members. Keep a minimum of seven feet between bottom of air cleaner and the floor surface Do not use rope, cable, or power cord to suspend the unit from the ceiling. Use chain rated for a minimum of a 150 lb. working load. IMPORTANT: The air cleaner will operate more efficiently when the air flow is unrestricted. Do not locate the unit in a corner or near heating or cooling vents. OPERATION OPERATIONAL CONTROLS AND ADJUSTMENTS CORD SWITCH The Air Cleaner is equipped with an in-line rocker switch (A) Fig. 5 on the power cord (B). To supply power to the machine, press down on the end of the rocker switch that has the white dot. To stop power to the unit, press down on the opposite end. Make sure that the switch (C) Fig. 5 is in the “OFF” position before plugging in the power cord. In the event of a power failure, move the switch to the “OFF” position. An accidental start-up can cause injury. MOTOR AND LIGHT PULL CORDS NOTE: The motor and light have independent pull switches, but the cord switch must be in the “ON” position for them to operate. To start and stop the air cleaner motor, pull down on the motor pull cord (C) Fig. 6. The motor pull cord (C) has a fan icon to indicate the motor pull cord. To turn the light "ON" and "OFF", pull down on the light pull cord (D) Fig. 6. The light pull cord (D) has a bulb icon to indicate the light pull cord. Fig. 5 B A C FAN ICONLIGHT ICON Fig. 6 C D MACHINE USE NOTE: The air cleaner may produce a slight odor for the first few hours of operation because of the protective coating applied to internal components. This odor will dissipate and should be disregarded. Never operate the air cleaner without air filters in place. The air cleaner can be used in the overhead position, on a work bench, or on the floor. The Delta AP100 Air Cleaner can be used for: a. sanding applications. b. sawing applications. c. dry wall applications. d. any application where non-metallic dust is a factor. 9 99 TROUBLESHOOTING TROUBLESHOOTING For assistance with your machine, visit our website at for a list of service centers or call the DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582). MAINTENANCE CHANGING AND CLEANING FILTERS Disconnect unit from the power source! 1. Remove the six screws (A) Fig. 7 from the filter cover. 2. Pull the filter cover (C) Fig. 8 from the machine. A C Fig. 7 Fig. 8 3. Remove the three spring clips (D) Fig. 9 4. Remove the bag filter (E) Fig. 9. 5. Remove the pre-filter (F) Fig. 10. 6. Depending on the condition, you can either clean or replace the filters (E) Fig. 9 and (F) Fig. 10. Clean the filters either with a shop-vac or with compressed air. Compressed air can be dangerous. For operator safety, do not exceed 30 psi. Do not point the air nozzle toward yourself or anyone else. Always wear safety glasses and dust mask when performing this procedure. 7. Perform this operation in reverse to install the filters. 8. Replace the filters on the opposite side of the machine in the same manner. E D F Fig. 9 Fig. 10 10 1010 LIGHT STARTER NOTE: The starters supplied with this machine are standard fluorescent starters (fs-2). Disconnect unit from the power source! 1. To remove the starter (A) Fig. 11, turn the starter (A) counter clockwise until it stops. Pull the starter out. 2. Insert a new starter by aligning the two prongs (B) Fig. 12 with the two holes (C) in the starter holder. Turn the starter clockwise until it stops. A B Fig. 12Fig. 11 C KEEP THE UNIT CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear certified safety equipment for eye, hearing and respiratory protection while using compressed air. FAILURE TO START Should your unit fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in the line. 11 1111 SERVICE SERVICE REPLACEMENT PARTS Use only identical replacement parts. For a parts list or to order parts, visit our website at servicenet.deltamachinery. com. You can also order ...
Эта инструкция также подходит к моделям:Воздухоочистители - AP-100 (857.93 kb)