. . . . . . . . . . . . . . . .2 Specification Guidelines . . . . . . . . . . . . .3 Installation Instructions Before Beginning Installation . . . . . . . .4 Faucet Drain Tubing and Water Supply Tubing . . . . . . . . . . . . . . . .8 Faucet Installation . . . . . . . . . . . . . . . . . .7 Filtration Drain Connection . . . . . . . . . .8 System Assembly . . . . . . . . . . . . . . . . . . .9 Things to Check Before Installation . . . . . . . . . . . . . . . . . . .5 Tools and Materials Required

VALVE OUTLET i OPEN A NEARBY SOFT WATER FAUCET i 000 to 199 (continuaD = Repeats display for each gallon of water passing through the meter. B° The letter (P) and clash (or dashes) indicate POSI- If you don't get a reading in the display, with the TION switch operation. If the letter appears, the faucet ()pen, pull the sensor from the valve outlet switch is closed. If the clash shows, the switch is port. Pass a small magnet back and forth in front of ()pen. the sensor. You should get a reading i

This manual is a reference and will not include every system installation situation. The person installing this equipment should have: • Knowledge of water conditioning and how to determine proper Left Side Right Side control settings • Basic plumbing skills • The directional instructions "left" and “right" are determined by looking at the front of the unit. Icons That Appear In This Manual WARNING: Failure to follow this instruction can result in personal injury or damage to the equipment. NOTE

The words “Regeneration Time” will scroll through the banner display. To change the regeneration time press and hold the UP or DOWN button until the desired regeneration time is displayed. Press SET to lock this time into memory. NOTE: When the controller is set up for a twelve hour clock a PM indicator will illuminate when the displayed time is in the PM hours. There is no indicator for the AM times. Level I Programming Rev A Level II Programming Level II program parameters are those parameters

You must follow these guidelines as you install the Water Filtration System. • Be sure the water supply conforms with the Performance Data. If the water supply conditions are unknown, contact your municipal water company. • Commonwealth of Massachusetts Plumbing Code 248 CMR shall be adhered to. The use of saddle valves is not permitted; please consult your local plumber. WARNING — Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before o

5 Align the cap with the filter housing (lights in the front) and press it down into place. NOTE: The cap is designed to fit on the filter housing only one way. 6 Slowly turn on the water supply and check for leaks. NOTE: If leak occurs at filter, turn cartridge to make sure it is fully sealed. 7 With the cold water fully open, turn the selector dial to “Filtered Water” to begin flushing the system. Flush the new filter cartridge for 10 minutes to remove any harmless carbon fines that may be in

Also, before sanitizing, be sure to remove all cartridges as described in the Sanitizing the Reverse Osmosis System section. Chlorine will destroy the Reverse Osmosis cartridge. 1 Complete Cartridge Replacement and Sanitize the System procedures (see pages 6–8), except reinstall the filters provided with the unit. 2 Purge membrane. See Step 12 in Reverse Osmosis Cartridge Replacement section. 3 Carefully check the system for leaks. Installation Checklist 1. Are all tubing connections tightened?

Rinse well. 5 6 Remove cap from RO cartridge housing (unscrew tubing first, on some models). Use pliers to remove the RO cartridge. Place in a clean plastic bag or discard if replacing. Thoroughly wipe inside of housing and cap with a paper towel or dish brush moistened with dish soap. Rinse well. 7 Replace empty postfilter sump. 8 Fill prefilter sump with water to within 1. of O-ring. Add 2 oz. (4 Tbsp.) ordinary household bleach. Replace prefilter sump. 9 Turn on water supply. Open RO faucet u

water iron). To take red water iron out of water, or over the maximum of clear water iron, an iron filter or other equipment is needed. GE recommends using only Diamond Crystal® Red•Out® brand salts with Iron Fighter® additive to help keep the resin bed clean of clear iron. If your water supply has clear water iron, periodic resin bed cleaning is needed. GE recommends using Super Iron Out® brand resin bed cleaner to thoroughly clean your resin bed if your iron content is high. Clean the bed at l

from the resin bed and to the drain. Brining Fast Rinse During brining, brine travels from the salt storage Backwash is followed by a fast flow of water area into the resin tank. Brine is the cleaning down through the resin tank. The fast flow agent needed to remove hard minerals from the flushes brine from the bottom of the tank, resin beads. The hard minerals and brine are and packs the resin bed. discharged to the drain. After fast rinse, the water softening system The nozzle and venturi crea