Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
Position in "bypass" only if needed for softener repairs. See FIG. 14, page 4-1 of this manual. w" Is the valve drain hose connected the and without sharp bends or kinks stop or reduce water flow? See page installation manual. right that 3-5 way, could in the Page numbers Manual unless referred otherwise to are in noted. the Installation p" Is the transformer plugged into an inside, always live, grounded, 120VqSOHz electrical outlet? See pages 3-8 and 3-9 in the installation manual, and the wiring schematic on page 5-1 of this manual. plastic 3-valve (.i _r/L_ Be sure 3-9. to restart the water heater. See page Bypass Valve(s) NOTE: Codes in the state of Massachusetts require installation by a licensed plumber. For installation, use plumbing code 248-CMR of the Commonwealth of Massachusetts. 1-2 Problems, Questions? Call 1-800-426-9345 Kenmore Water Line _iii_i_i_i_iii_ii SECTION 1 ii_iiiii;i_iiiiii_!i_iiiit WATER SOFTENER START UP C. PROGRAM THE TIMER display UP button DOWN button F [ \ \ ! Customer AssJstar_ce 1-800-426-9_5 RECHARGE NOW RECHARGE TONIGHT ON/OFF-HOLD button SELECT button (Recharge Tonight-Now) When the transformer is plugged in, a model code, SOUND "BEEPER": A "beeper" sounds while and a test number (example: $3.0) show in the face pressing buttons for timer set-up. One beep signals plate display for 4 seconds. Then, 12:00 AM and a change in the face plate display. Repeated beeps PRESENT TIME begin to flash. mean the timer will not accept a change from the button you have pressed, telling you to use another UitraSoft 100 button. For example, while setting the hardness COOE (step 2), the beeper sounds repeatedly when the dis play reaches I using the DOWN button, or the high 5R22 IS3.0 est hardness setting using the UP button. B SET PRESENT TIME OF DAY i _'w..JW I PRESENT TIME | If the words PRESENT TIME do not show in the dis- UltraSoft 150 play, press the SELECTbutton (FIG. 2) until they do, or see the previous notes. 5R2H [530 • Press the UP / DOWN buttons to set the present • COOE time. Press UP to move the display ahead; press DOWN to move the time backward. J _.rlr-_ u If the present time is between %B"I noon and midnight, be sure PM shows. Notes: TIME j PRESENT If SR --shows in the display, press the UP (_ or If the present time is between DOWN (_ button until SR22 or SR24 shows. Then, midnight and noon, be sure AM press the SELECT button to set, and change to the shows. flashing PRESENT TIME display. To check the model code, unplug the transformer at Each press of the UP /DOWN buttons changes the wail outlet and ptugin again, if other than SR22 the time by one minute. Holding the buttons in or SR24 shows, see page 5-3 to reset. changes the time rapidly. 1-3 Problems, Questions? Call 1-800-426-9345 Kenmore Water Line C. PROGRAM THETIMER • Press the UP / DOWN buttons to set the desired B SET WATER HARDNESS NUMBER recharge starting hour. Be sure to observe the AM • Press the SELECT button once to display 25 PM as you did when setting the present time of day. (flashing) and HARDNESS. Note: The grains per gallon (gpg) hard- Each press of the UP / DOWN buttons changes the ness of your water supply is on display I hour. Holding the buttons in changes the your water analysis report. Be display twice each second. sure to enter water test results on page A, for future reference. _SET SALT EFFICIENCY If your water supply contains iron, compensate for A new feature in this modelis Salt Efficiency. When it by adding to the water hardness number. For ex- this feature is ON, the unit will operate at salt effi ample, assume your water is 20 gpg hard and contains 2 ciencies of 4000 grains of hardness per pound of salt ppm iron. Add 5 to the hardness number for each I ppm or higher which will reduce the softeners salt usage. of iron. In this example, you would use 30 for your hardness number. • Press and hold for 3 seconds the SELECT button until the following screen is displayed. 20 gpg hardness 2 ppmironx5 = 10 +10 (times) 30 HARDNESS NUMBER .,o • Press the UP / DOWN buttons to set your water I hardness number in the display. The DOWN button WATER (A) (B) METER SWlTGH moves the display to 1. The UP button moves the More information on this particular display is display to the highest setting (see maximum setting found in the Troubleshooting Section of the manual, for your model in the specifications). under Manual Initiated Electronics Diagnostics. Note: Each press of the UP / DOWN button changes the • Once in this display, press the SELECT button and display by I between I and 25. Between 25 and the one of the following two displays is shown. highest number, the display changes 5 at a time... 25, 30, 35, etc. Holding the UP or DOWN button in changes the display twice each second. _I _SET RECHARGE (REGENERATION) TIME • Press the UP button to set this feature ON, press • Press the SELECT button to display 2:00 A_M the DOWN button to set OFF. When the Salt Effi (flashing) and RECHARGE TIME. 7,1717 A_ ci...
Эта инструкция также подходит к моделям:Водоочистители - 625.38816 (1.13 mb)