Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
If it becomes plugged with sand, silt, dirt, etc., the softener will not work and you will get hard water. O-ring Seal _.___ Screen Support To get to the nozzle and venturi, remove the softener top cover. Be sure the softener is in service cycle (no water pressure at nozzle and venturi), Screen then turn off the cap from the nozzle and venturi _'_ (1-EP) Nozzle & Venturi +_/*Flow Plug housing. Do not lose the large o-ring seal. Lift out the screen support and screen, then the nozzle and venturi. Wash and rinse the parts in warm water IMPORTANT: Be sure Gasket __ _ Screen_. _ until clean. If needed, use a small brush to remove holes in the gasket are ceniron or dirt. Also check and clean the gasket, flow tered directly over the small holes in the nozzle & venturi plugs and screens. housing, *Flow Plug Carefully replace all parts in the correct order. (HVDC) Lubricate the o-ring seal with silicone grease or Nozzle & Venturi Vaseline and place in position. Install and tighten Housing the cap, by hand only. Do not overtighten and *Install with numbered side up concave break the cap or housing. side down. Be sure the largest flow plug is located in the nozzle & venturi housing. IRON FROM THE RESIN BED water iron, an iron filter or other equipment is needed. Your local Sears store has trained people to Your water softener takes hardness minerals (calhelp you with iron water problems. cium and magnesium) out of the water. Also, it can control some "clear water" iron. See maximum If your water supply has clear water iron, even allowed in the specifications on page 19. With clear though less than the maximum allowed, regular water iron, water from a faucet is clear when first resin bed cleaning is needed. Sears has resin bed put into a glass. After 15 to 30 minutes, the water cleaner, Item No. 42-34426 for this. Clean the bed at begins to cloud or turn rust colored. A water least every 6 months. If iron shows up in the soft softener WILL NOT remove any iron which makes water before 6 months, clean more often. Printed the water cloudy or rusty as it comes from the instructions are on the resin bed cleaner bottle. faucet (called red water iron). To take red water iron out of water, or over the maximum of clear 16 SECTION 3 cAREoFYour so .ER 30. KEEP THE SOFTENER FROM FREEZING If the softener is installed where it could freeze (summer cabin, lake home, etc.), you must drain all water from it to stop possible freeze damage. To drain the softener - 1. Close the shut-off valve on the house main water pipe, near the water meter or pressure tank. . Open a faucet in the soft water pipes to vent pressure in the softener. ° Refer to FIG. 12 on page 19. Move the stem in a single bypass valve to bypass. Close the inlet and outlet valve in a 3-valve bypass system, and open the bypass valve. If you want water in ° the house pipes again, reopen the shut-off valve on the main water pipe. ° Unplug the transformer at the wall outlet. Remove the salt hole cover and the main cover. Take off both drain hoses. ° Carefully remove the large holding clips at the ° softener inlet and outlet (see Key No. 69, on page 30). Separate the softener from the copper tubes, or from the bypass valve. ° Remove the brinewell cover and disconnect the brine valve tubing at the nozzle and venturi assembly (see page 30). Lift the brine valve out of the brinewell. Tip the brine valve upside down to drain water. DRAIN WATER FROM THE SOFTENER drain wood block Looking at FIG. 11, lay a piece of 2 inch thick board near the floor drain. Move the softener close to the drain. SLOWLY and CAREFULLY, tip it over until the rim rests on the wood block with the inlet and outlet over the drain. Do not allow the softener's weight to rest on the inlet and outlet fittings or they will break. Tip the bottom of the softener up a few inches and hold until all water has drained. Leave the softener laying like this until you are ready to use it. Plug the inlet and outlet with rags to keep dirt, bugs, etc. out. 17 SECTION 3 CARE OF YOUR SOFTENER 3D. HELPFUL HINTS CHECKLIST ... TO HELP YOU SAVE MONEY If your water softener fails to work make the following easy checks. Often, you will find what's wrong yourself and you won't have to call and wait for service. If you do not find anything wrong, while making the checks, and your softener still does not work, call your Sears Service Department. NOTES: 1. Also read ERROR CODE, page 11. 2. If an error code is not displayed, press and hold the SELECT button until the display changes. Then, press the SELECT button again and hold until a flashing HF code appears. It must show HF31. If any other number shows, the face plate computer is working on incorrect input and would probably be the cause of the problem. To set HF31, press either the UP [] or DOWN[] button. When HF31 shows, press SELECT to return a flashing 12:00 AM display. Reset the present time, hardness number, etc., pages 6 and 7. PROBLEM CAUSE CORRECTION No soft water No salt (or sa...