Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
CARTRIDGE REPLACEMENT (for UVS-110 and UV-110 only) Your cartridge should be replaced when there is a noticeable drop in water flow at the faucet or tap, and/or when unpleasant odors return (approximately every 6-9 months). 1. Turn off water supply to the system. 2. Open faucet to relieve water pressure to the housing. 3. Unscrew housing from cap. If housing sticks or is difficult to open use an Pentek spanner wrench. 4. Remove used cartridge from housing, remove Teflon® sleeve and discard cartridge. 5. Remove O-ring from groove below the threads of the housing and wipe groove and O-ring clean. Lubricate O-ring with silicone grease. Place O-ring back into the groove. With two fingers wipe or press O- ring down into the groove. NOTE: This step is important to ensure a proper filter seal. Make sure that the O-ring is seated level in the groove. 6. Insert a new cartridge into the sump making sure that it slips down over the sump standpipe. 7 Remove gasket from cartridge end and slide Teflon® sleeve into center of cartridge then replace gasket on top of cartridge. 8. Screw the sump onto the cap and hand-tighten. Do not over-tighten. Make sure that the cap slips over the cap standpipe. 9. Turn on the water supply to allow the unit to slowly fill with water. 10. Check for leaks before leaving installation. Each time that you use water from your unit for drinking or cooking purposes, it is recommended that you run (flush) the tap for at least 10 seconds prior to using water. This is particularly important if the water tap is not used daily. UV LAMP REPLACEMENT 1. Turn off all electrical power to the system by unplugging or throwing the circuit. 2. Unscrew the UV control module from the mounting bracket (4 screws) for Models UV-110, UV-120 and UVBB-120. For Model UVS-100, slide mounting bracket retainer to allow access to the UV bulb. 3. Slide the old bulb out and unplug from the control module. NOTE: Hold the UV lamp only by the plastic covered ends of the bulb. 4. Carefully discard the old UV lamp. 5. Holding the new UV lamp only by the plastic covered ends of the bulb, plug the new UV lamp into the control module or power cord. Slide the new bulb into the cartridge housing and reattach UV control module or secure mounting bracket retainer (depending on model). 6. Restore electrical power to unit. 7. Check for leaks. UVS-110 REPLACEMENT PARTS Part Description Part # 1. 10” SlimLine™ Housing 153017 2. O-ring 143026 3. CBU-10 155271-03 4. Teflon® Sleeve 163518 5. Quartz Sleeve 163504 6. O-rings for Quartz Sleeve 163538 7. 1/2” Blk Cap w/o pr SPECIAL ORDER 8. Spacer Bushing 163517 9. Mounting bracket SPECIAL ORDER 10. UV lamp 163503 11. Control Module (120v/60Hz) 163501 for use with UVS-110-1 Control Module (220v/50Hz) 163502 for use with UVS-110-2 12. SW-1 Wrench (not shown) 150539 UV-110 REPLACEMENT PARTS Part Description Part # 1. 10” Housing 153001 2. O-ring 143011 3. CBU-10 155271-03 4. Teflon® Sleeve 163518 5. Quartz Sleeve 163509 6. O-rings for Qua...
Эта инструкция также подходит к моделям:Водоочистители - PENTEK UV-110 (56.25 kb)
Водоочистители - PENTEK UVBB-120 (56.25 kb)
Водоочистители - PENTEK UVS-110 (56.25 kb)