Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
For example, if the valve is in transition between fill and brining, both Fill and Brine flash. Upon reaching brining position, Fill goes off and Brine is on steady. The time display shows the minutes of the cycle remaining. NOTE: If the faceplate is left in a diagnostic display (or a flashing display when setting times or hardness), present time automatically returns if a button is not pressed within 4 minutes. To return to the diagnostic display, repeat step 1. OTHER INFORMATION While in this diagnostic screen, the following information is available and may be beneficial for various reasons. This information is retained by the computer from the first time electrical power is applied to the faceplate. • Press and hold the UP button to display the number of days this faceplate has had electrical power applied. • Press and hold the DOWN button to display the number of regenerations initiated by this faceplate since the model code number was entered. • Press the RECHARGE button to advance the valve to each position and observe the switch and position indicators to verify component operation, or to possibly isolate a defect. • Press and hold the SELECT button for 3 seconds until either S 32 or S 33 shows in the display, see Fig. 56. This code identifies the softener nominal capacity size. If the wrong number shows, the softener will operate on incorrect programming. Do the following as needed. S 32 or S 33 does show: Press the SELECT button to return to the present time display. To change the number: Press the UP or DOWN but- Position markers (Valve in service) MOTOR OUT IN FIG. 55 TIMER PWA REPLACEMENT Be sure the valve is in service position when replacing the timer PWA (observe valve cycle indicator). If after installing and programming the replacement timer PWA, the valve is not in service position, do the following to assure correct cycle orientation, or timing, between the faceplate and valve. Use the MANUAL ADVANCE procedures with the REGENERATION button, advance through the recharge cycles until the valve stops in service position, and RECHARGE no longer flashes in the display. NOTE: The valve motor may automatically drive through several valve positions while searching for service. If an error code occurs, unplug the transformer, then plug in again. Model 38356 Model 39356 ton until the correct code shows. Then, press the FIG. 56 SELECT button and reset the timer. Questions? Call The Kenmore Water Line 1-800-426-9345 Service Tech Information MANUAL ADVANCE REGENERATION CHECK This check verifies proper operation of the valve motor, brine tank fill, brine draw, regeneration flow rates, and other controller functions. Always make the initial checks, and the manual initiated diagnostics. NOTE: The faceplate display must show a steady time (not flashing). If an error code shows, first press the SELECT button to enter the diagnostic display. 1. Press the REGENERATION button and hold in for 3 seconds. *RECHARGE and Fill begin to flash (or clean backwash begins, if set) as the softener enters the fill cycle of regeneration. * NOTE: If the CLEAN feature is set to ON, a cleaning backwash (CLEAN and Bkwsh or Rinse flashes in the display, along with the minutes of the clean cycle remaining), precedes the recharge. 2. When FILL is on steady, remove the brinewell cover and, using a flashlight, observe fill water entering the tank. 3. If water does not enter the tank, look for an obstructed nozzle, venturi, fill flow plug, brine tubing, or brine valve riser pipe. CYCLE FLOW RATES (GALLONS PER MIN.) FILL (flow to salt storage tank) 0.3 (1.1 liters) BRINING (flow to drain) .22 (.83 liters) BRINE RINSE (flow to drain) .15 (.57 liters) MAX. BACKWASH (flow to drain) 2.0 (7.6 liters) MAX. FAST RINSE (flow to drain) 2.0 (7.6 liters) 4. After observing fill, press the REGENERATION button to move the softener into brining. A slow flow of water to the drain will begin. Verify brine draw from the brine tank by shining a flashlight into the brinewell and observing a noticeable drop in the liquid level. NOTE: Be sure a salt bridge is not preventing water with salt contact. 5. If the softener does not draw brine: • nozzle and/or venturi dirty or defective. • nozzle and venturi not seated properly on gasket • restricted drain (check drain fitting and hose) • defective nozzle and venturi seal • other inner valve defect (rotor seal, rotor & disc, wave washer, etc.) NOTE: If water system pressure is low, an elevated drain hose may cause back pressure, stopping brine draw. Float Stop Float 10” Brine Valve Float Setting FIG. 57 6. Again press REGENERATION to move the softener into backwash. Look for a fast flow of water from the drain hose. 7. An obstructed flow indicates a plugged top distributor, backwash flow plu or drain hose. 8. Press RECHARGE to move the softener into fast rinse. Again look for a fast drain flow. Allow the softener to rinse for a few minutes to flush out any brine that may remain in the resin tank from the brinin...
Эта инструкция также подходит к моделям:Водоочистители - 350 Series (3.15 mb)