Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
The DOWN button moves the display to 1. The UP button moves the display to the highest setting (see maximum setting for your model in the specifications). NOTE: Each press of the UP or DOWN button changes the display by 1 between 1 and 25. Between 25 and the highest number, the display changes 5 at a time (25, 30, 35, etc.) Holding the UP or DOWN button in changes the display twice each second. Present Time: Present Time: _Av _PM /_ V CHANGE SELECT A V CHANGE SELECT FIG. 26 /_ V CHANGE SELECT FIG. 27 Questions? Call The Kenmore Water Line 1-800-426-9345 SET REGENERATION TIME To complete setting the regeneration time, complete the following steps: 1. Press the SELECT button to display 2:00 AM (flashing) and RECHARGE TIME. 2. At the 2:00 AM recharge time setting, the softener begins regeneration (see pages 29 -31) at 2:00 AM. This is a good time in most households because water is not being used. If a different recharge time setting would be better for your household, complete the following step. 3. Press the UP or DOWN buttons to set the desired recharge starting hour. Be sure to observe the AM-PM as you did when setting the present time of day. Note: Each press of the UP or DOWN buttons changes the display one hour. Holding the buttons in changes the display twice each second. 4. Press the SELECT button once again, to complete initial programming, and the current time of day shows in the display. Normal Operating Screen has several useful items that can be viewed at a glance. The black bars on the left col umn display the amount of salt in the storage tank. The present time is shown in the upper right hand corner. Options are shown in the top center of the display. If the unit is going to recharge tonight or is in a recharge, this is shown. By pressing the Up arrow displays the "More" screen. "More" Screen shows the water used today, average daily use, average pounds of salt used per recharge and recharge count. If the recharge count is reset to zero, the average pounds of salt per recharge is reset also. PROGRAM MEMORY If electrical power to the softener goes off, the time display is blank but the face plate timer keeps the correct time for about 72 hours. When electrical power comes on again, you have to reset the present time only if the Set Present Time display is showing. The HARDNESS and RECHARGE TIME never require resetting unless a change is desired. Even if the timer is incorrect after a long power outage, the softener works as it should to keep your water soft. However, regenerations may occur at the wrong time of day until you reset the timer to the correct time of day. Recharge Time: /_ V CHANGE SELECT FIG. 28 _ 5:39 pM _ _ Water Recharge Flow Tonight More FIG. 29 Questions? Call The Kenmore Water Line 1-800-426-9345 SANITIZE THE WATER SOFTENER Care is taken at the factory to keep your water softener clean and sanitary. Materials used to make the softener will not infect or contaminate your water supply, or cause bacteria to form or grow. However, during shipping, storage, installing and operating, bacteria could get into the softener. SANITIZE YOUR WATER SOFTENER AS FOLLOWS: 1. Be certain the bypass valve is pulled out to "service" position. 2. Liftthe salt hole cover and use a pail add up to 3 gallons of water to the salt storage tank. 3. Remove the brine well cover (Fig. 30) and pour about 3/4 ounce, or 1 to 2 tablespoons, of common 5.25% 1, unscented, household bleach (Clorox, Linco, BoPeep, White Sail, Eagle, etc.) in the softener brinewell. Replace the brinewell cover. 4. Press the REGENERATION button and hold for 3 seconds to start a recharge. This first recharge does several things. • It draws the bleach into and through the softener to sanitize it. • It fills the salt tank to the water level needed. • It gets all the air out of the resin tank. • It prepares the resin bed (see page 26) for service and flushes residual chlorine from the softener. NOTE: This recharge takes about 2-1/2 to 2-3/4 hours, depending on the salt type setting. NOTE: During a recharge the water softener bypasses raw water to the home. You will not get salty water or affect the regeneration cycle if water is used at this time. You can sanitize the softener with or without salt in the storage tank. 1Recommended by the Water Quality Association. On some water supplies, the water softener may need periodic disin fecting. Your new Sears softener is now softening the water for your household needs. However, your WATER HEATER is filled with hard water. To have fully soft water right away, you can drain the water heater so it refills with soft water. If you don't drain the water heater, it will take a few days before you have fully soft water. To drain the water heater, open a hot water faucet and let it run until the water runs cold. Then close the faucet. NOTE: If this procedure is performed on a new softener, water coming from the taps may initially be discolored. This normally occurs the first time water runs through t...