Оценок - 2, средний балл: 3 ( )

Производитель: Desa Размер: 4.93 mb Название файла: Язык инструкции:

The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of the central heating system, etc. Note: Selecting the HI setting with the control knob will cause the burners to remain fully on, without modulating down in most cases. 1. Follow steps 1 through 5 under Lighting Instructions, page 19. 2. Depress control knob and light pilot with match. 3. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow step 8, under Lighting Instructions, column 1. MANUAL LIGHTING PROCEDURE Figure 37 - Control Knob and Ignitor Button Location Figure 38 - Pilot CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve. LO HI OFF Pilot Ignitor Button Control Knob OPERATING HEATER Continued TO TURN OFF GAS TO APPLIANCE Shutting Off Heater Turn control knob clockwise Clockwise to the OFF position. Shutting Off Burners Only (pilot stays lit) Turn control knob clockwise Clockwise to the PILOT position. Thermocouple Ignitor Electrode Pilot Burner 6. With control knob pressed in, press and release ignitor button. This will light pilot. The pilot is attached to the front burner. If needed, keep pressing ignitor button until pilot lights. Note: If pilot does not stay lit, contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure. 7. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Note: If pilot goes out, repeat steps 3 through 7. This heater has a safety interlock system. Wait one (1) minute for system to reset before lighting pilot again. 8. Turn control knob counterclockwise C-clockwise to desired heating level. The burners should light. Set control knob to any heat level between HI and LO. OPERATING HEATER (Thermostatically-Controlled Models) Lighting Instructions (Cont.) To Turn Off Gas to Appliance Thermostat Control Operation Manual Lighting Procedure INSPECTING BURNERS Pilot Flame Pattern INSPECTING BURNERS Burner Primary Air Holes Main Burner CLEANING AND MAINTENANCE Cleaning Burner Injector Holder and Pilot Air Inlet Hole Logs Main Burner 21 INSPECTING BURNERS Continued BURNER PRIMARY AIR HOLES 4. Check the injector holder located at the end of the burner tube again. Remove any large particles of dust, dirt, lint, or pet hair Air is drawn into the burner through the holes in the fitting at the with a soft cloth or vacuum cleaner nozzle. entrance to the burner. These holes may become blocked with dust, 5. Blow air into the primary air holes on the injector holder. lint, or pet hair. Periodically inspect these holes for any blockage and clean as necessary. Blocked air holes will create soot. 6. In case any large clumps of dust have now been pushed into the burner repeat steps 3 and 4. MAIN BURNER Clean the pilot assembly also. A yellow tip on the pilot flame Periodically inspect all burner flame holes with the heater running. All indicates dust and dirt in the pilot assembly. There is a small pilot slotted burner flame holes should be open with yellow flame present. air inlet hole about two inches from where the pilot flame comes out All round burner flame holes should be open with a small blue flame of the pilot assembly (see Figure 42). With the unit off, lightly blow present. Some burner flame holes may become blocked by debris or air through the air inlet hole. You may blow through a drinking straw rust, with no flame present. If so, turn off heater and let cool. Remove if compressed air is not available. blockage. Blocked burner flame holes will create soot. Burner TubePrimary AirInlet Holes Injector Holder CLEANING AND MAINTENANCE WARNING: Turn off heater and let cool before cleaning. CAUTION: You must keep control areas, burner, and circulating air passageways of heater clean. Inspect these areas of heater before each use. Have heater inspected yearly by a qualified service person. Heater may need more frequent cleaning due to excessive lint from carpeting, bedding material, pet hair, etc. CLEANING BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLE The primary air inlet holes allow the proper amount of air to mix with the gas. This provides a clean burning flame. Keep these holes clear of dust, dirt, lint, and pet hair. Clean these air inlet holes prior to each heating season. Blocked air holes will create soot. We recommend that you clean the unit every three months during operation and have heater inspected yearly by a qualified service person. We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 PSI. Your local computer store, hardware store, or home center may carry compressed air in a can. You can use a vacuum cleaner in the blow position. If using compressed air in a can, please follow the direction...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: