Оценок - 5, средний балл: 4.6
(
)
)
|
Фрагмент инструкции
dealer where you bought heater for proper type heater. INSTALLING HEATER TO WALL Marking Screw Locations 1. Determine where you will locate heater. WARNING: Maintain minimum clearances shown in Figure 5. If you can, provide greater clear- INSTALLATION ITEMS Before installing heater, make sure you have the items listed below. • external regulator (supplied by installer) • piping (check local codes) • sealant (resistant to propane/LP gas) • equipment shutoff valve * • ground joint union • test gauge connection * • sediment trap • tee joint • pipe wrench * A CSA/AGA design-certified equipment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connec- IMPORTANT:Vent-free heaters add moisture to the air. Although this is beneficial, installing heater in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Combustion and Ventilation, pages 4 through 6. ances from floor and joining wall. 2. Mark two mounting screw locations on wall (see Figure 5). tion. The optional CSA/AGA design-certi CAUTION: If you install the fied equipment shutoff valve can be pur heater in a home garage chased from your dealer. See Accessory, • heater pilot and burner must page 13. be at least 18 inches above floor • locate heater where moving vehicle will not hit it • where there is easy access for operation, inspection, and service Mounting Screw Locations 20 1/4" 8 7/8" Minimum To Maintain 6" Clearance From Wall 7 3/4" Minimum To Maintain 3" Clearance From Floor FLOOR JOINING WALL Figure 5 - Mounting Screw Locations • in coldest part of room Continued 104268 7 For convenience and efficiency, install heater VENT-FREE PROPANE/LP GAS HEATER INSTALLATION Continued Installing Two Mounting Screws Note:Wall anchors and mounting screws are in hardware package. The hardware package is provided with heater. Attaching To Wall Stud Method For attaching mounting screw to wall stud 1. Drill hole at marked location using 9/64" drill bit. 2. Insert mounting screw into wall stud. 3. Tighten screw until 1/16" space (thickness of penny) is between screwhead and wall. Attaching To Wall Anchor Method Follow instructions below to attach mounting screws to hollow walls (wall areas between studs) or solid walls (concrete or masonry). 1. Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1 1/4" deep. 2. Fold wall anchor (see Figure 6). 3. Insert wall anchor (wings first) into hole. Tap anchor flush to wall. 4. For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings (see Figure 7). IMPORTANT:Do not hammer key! For thick walls (over 1/2" thick) or solid walls, do not pop open wings. 5. Tighten two screws until 1/16" space (thickness of penny) is between screwheads and wall (see Figure 8). Figure 6 - Folding Anchor Thin Walls (1/4" to 1/2" thick) Thin or Thick Wall (thick wall shown) 1/16" Space Solid Wall Figure 8 - Tightening Anchors Placing Heater On Mounting Screws 1. Locate two keyhole slots on back panel of heater (see Figure 9). 2. Place large openings of slots over screwheads. Slide heater down until screws are in small portion of slots. Keyhole Slots Figure 9 - Location Of Keyhole Slots On Back Panel Of Heater Removing Front Panel Of Heater 1. Remove two screws near bottom corners of front panel. 2. Lift straight up on grill guard until it stops. Grill guard will slide up about 1/4". 3. Pull bottom of front panel forward, then down. Installing Bottom Mounting Screw 1. Locate bottom mounting hole. This hole is near bottom on back panel of heater (see Figure 11). 2. Mark screw location on wall. 3. Remove heater from wall. 4. If installing bottom mounting screw into hollow or solid wall, install wall anchor. Follow steps 1 through 5 under Attaching To Wall Anchor Method, column 1. If installing bottom mounting screw into wall stud, drill hole at marked location using 9/64" drill bit. 5. Replace heater on wall. 6. Insert bottom anchor screw through back panel into bottom anchor or drilled hole (see Figure 11). 7. Tighten screw until heater is firmly secured to wall. Do not over tighten. Note:Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see pages 9 and 10 ). Figure 11 - Installing Bottom Mounting Screw Figure 7 - Popping Open Anchor Wings Figure 10 - Removing Front Panel OfFor Thin Walls Heater 8 104268 OWNER’S MANUAL INSTALLATION Continued CONNECTING TO GAS SUPPLY WARNING: This appliance requires a 3/8" NPT (National Pipe Thread) inlet connection to the pressure regulator. WARNING: A qualified service person must connect heater to gas supply. Follow all local codes. CAUTION: Never connect heater directly to the propane/LP supply. This heater requires an external regulator (not supplied). Install the external regulator between the heater and propane/LP supply. The installer must supply an external regulator. The external ...
Эта инструкция также подходит к моделям:Водонагреватели - CGP10TA (301.89 kb)