Оценок - 2, средний балл: 3.5 ( )

Производитель: Kenmore Размер: 1.27 mb Название файла: Язык инструкции:

overfire draft of -0.02 inches w,c. The burner settings provided are intended for initial start up only. Final adjustment must be made I NOTE: All burners use an inserti°n depth °f 2-1/4'' and fired at a using combustion test instruments. 38 I STATIC PLATE 3-5/8 3-1/2 3-1/2 3-1/2 3-3/8 3-3/8 2-3/4 2-3/4 2-3/4 OIL BURNER AFG F-HEAD AFG F-HEAD AFG F-HEAD AFG F-HEAD AFG F-HEAD AFG F-HEAC AFG 50 MD AFG 50 MD AFG 50 MD NOZZLES AND ELECTRODES: Use the proper size, spray angle, and spray pattern nozzle. Refer to the recommended nozzle selection charts at the end of this manual. To install a nozzle, remove the nozzle line electrode assembly, if necessary remove the retention ring assembly, and then install and tighten the nozzle. Be careful not to damage the electrode insulators or the bend the electrode tips. After installing the nozzle, reassemble the nozzle line electrode assembly and set the electrode tip spacing. Depending on the bumer purchased, the electrode tip spacing may need to be set prior to reassembling the nozzle line electrode assembly. Refer to the figures on the following pages for setting the electrode tip spacing on Beckett, Carlin, and Riello t_umers. FINAL BURNER ADJUSTMENTS: Final burner adjustments must be made using combustion test instruments. Initial settings for the burner are shown at the back of this manual. Set the burner accordingly. Check the draft over fire to verify that it is between M).01" WC and -0.02" WC, otherwise adjust the draft as necessary. After operating 10 minutes to warm up the boiler, use the combustion test equipment to take a smoke reading in the flue pipe between the boiler and the draft regulator. The smoke reading should be zero to a trace (Shell Bacharach Scale). At times a new boiler requires more than 10 minutes to burn clean due to the oil film on the new heat exchanger. If the smoke reading is zero, gradually close the burner's air adjustment to obtain a smoke reading showing a trace smoke reading. Once the smoke reading is a trace, measure the COz and as an insurance margin increase the air to sufficiently reduce the CO2 by 1/2% to 1%. Ira clean fire cannot be obtained, it will be necessary to verify the burner head and electrode alignment. Proper electrode alignment figures are presented on the following pages. If the fire continues to be smoky, replace the nozzle with a correct replacement. Once the burner is completely adjusted, the burner should be started and stopped several times to assure good operation with no fluttering or rumbling. Verify that there are no oil leaks and then record the nozzle size, oil pressure, combustion readings, and air settings on a tag or label that can be attached to the burner or boiler. OIL BURNER MAINTENANCE: For the Becket/: AFG, Carlin EZ-1 or EZ-2, and the Riello 40 F3, F5, or F10 the following preventative maintenance items should be performed annually, preferably prior to the heating season. 1. Oil Burner Motor -For Beckett and Carlin burners, add 2 -3 drops of non-detergent electric motor oil to each oil cup located at the front and rear of the motor (Riello burners are permanently lubricated). Excessive oiling will shorten the life expectancy of the motor. 2. Fuel Filter -This should be replaced so as to prevent contaminated fuel from reaching the nozzle. A partially blocked fuel filter can cause premature failure of the fuel pump. 3. Fuel Pump Unit -Replace pump screen and clean pump unit to maintain fuel delivery to the nozzle. 4. Ignition Electrodes -Clean and adjust as per manufacturer's recommendations, so as to maintain reliable ignition of oil. 5. Nozzle -Replace so as to maintain safe and reliable combustion efficiency. Always replace with the exact nozzle as required in the charts in the back of this manual. 6. Fan and Blower Housing These must be kept clean, free of dirt, lint and oil so as to maintain the proper amount of air the fuel requires to burn. 7. Check the final burner adjustments. i I NOTE:parts If any component recommended parts must be replaced, always I use by the burner manufacturer. I 2l BECKETT AFG BURaNER ELECTRODE ADJUSTMENTS VARIABLE (VI) HEADS BOILER DIMENSION "'N" DIMENSION "H" MODEL (electrode to nozzle) (head to nozzle) 5EW 1/16" 7/32" to 9/32" lMENSION "}'1" SEE BELOW--\_ 5132 ,,. .._.._CTROOE GAP " " _ ..,a LI or VI HEAD _.. _DIMEMBION -N" E B.LOW BECKETT AFG VARIABLE (V1) HEAD ADJUSTMENTS AND SETTINGS _Lfrl LOC:I w&Ja4_ /_" s_JUST,UK.( ).4[A0 A_lr T'Jll.( BECKETT AFG BURNER ELECTRODE ADJUSTMENTS F-HEADS Burner F-Head Model DIMENS1ON"N" (head to nozzle) F0 thru F31 1/16" _ELECTROOE .E 22 5/32" -4mm ,) 5/64" to 7/64" or 2 to 2.5 m[__ "_ 5/32" or 4 mm E E 5/32" to 13/64" or4to5mm _ I _ i - TO 23 CHECKING AND ADJUSTING CONTROLS A boiler using a tankless coil is configured with a Honeywell L8124C Combination Hi/Low Limit Aquastat Relay (refer back to the SYSTEM PIPING section for more details). A boiler not using a tankless coil is configured with a Honeywell L8148A Hi Limit Aquast...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: