Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
For propane/LP gas you must remove it and replace it with an propane/ LP orifice. The hardware kit contains an propane/LP orifice with a red stripe for converting the pilot. 1. Gently loosen and remove the pilot line connection from the bracket (see Figure 17, page 11). 2. Be sure to use the correct orifice for your appliance. The hardware kit included with this appliance contains two orifices with a cone-like shape. If you have an 18" set, the orifice for the burner inlet fitting is red; for a 30" set, it is black. If you have a 24" log set, the orifice is already installed inside the fitting. 3. For an 18" or 30" set, use a 10mm socket or nut driver to remove the orifice from the propane/LP burner inlet fitting. Choose the correct orifice for your log set size and install in place of the orifice you just removed. 4. Using thread sealant (resistant to the action of propane/LP gas) on larger end of fitting, screw the burner inlet fitting through hole and into burner manifold. Tighten using a wrench. 5 . Follow steps 1 through 12 under Natural Gas Installation, pages 9 and 10. Inlet Opening 901048 11 OWNER’S MANUAL TESTING BURNER FOR LEAKS 1. Generously apply soapy solution to all connections. WARNING: Never check for gas leaks with open flame. 2. Light the burner with the shut-off valve no more than half open and holding a match slightly in front of the pan (see Lighting Instructions, page 12). 3. Inspect all connections for bubbles, raw gas odor, or flame from any area other than the burner (leaks). If leaks are detected, shut off the gas valve immediately. Tighten, or reassemble the loose connection(s) using pipe joint compound until burner system is leak free. 4. When the burner is tested and leak free, observe the individual tongues of flame on the burner. Note: The burner design includes more ports on the outside of the bar. Make sure that all ports are clear and producing flame evenly across the burner. If any ports appear blocked, clear them by removing the burner manifold and reaming the ports with a modified paper clip or other suitable tool. 5. When finished testing, turn the gas shutoff valve OFF to extinguish all flames. INSTALLATION Continued Figure 17 - Installing Propane/LP Pilot Orifice Pilot Injector Figure 18 - Installing Grate (Pan Material Not Shown) ADDING PAN MATERIAL 1. Open the bag of Ash Bed Material (vermiculite) and spread it evenly across the burner pan to the top. You may overflow the front and sides of the pan to cover the entire pan and connecting hardware. Do not cover GA9050 series or GA9150 series valve. 2. Open the glowing embers and evenly cover the Ash Bed Material (vermiculite) in the burner pan. INSTALLING THE GRATE AND LOGS 1. Place the grate over the burner pan where the two outer horizontal supports on the grate fit into the two pan positioning notches in the rear vertical edge of the pan. 2. Slide the two rear log grate steps over the two outer horizontal supports on the grate as shown in Figure 18 (Not Included with Oxford Oak Models). 3. Place the back log on the grate onto the grate steps (see Figure 19). If assembling Oxford Oak models, place log on the back of the grate bars (see Figure 19). 4. Place the front log(s) on the grate and slide forward against the front bars on the grate (see Figure 19). 5. Place the smaller top logs onto the bottom logs (see Figure 20). Leave as much open space between logs as possible to minimize flame impingement and sooting. Note: Logs may chip if they are handled roughly or if hit together while being placed. Figure 19 - Installing Front and Back Logs (Number and style of your logs may vary) Figure 20 - Placement of Top Logs (Berkshire Split Oak Logs Shown) Grate Grate Steps Berkshire Split Oak Logs 2. Replace the injector (see Figure 17) with the propane/LP pilot injector with the red stripe. 3. Replace and tighten the pilot line to the bracket. 4. Continue with step 3 under Natural Gas Installation, page 10. Amherst Oak Logs Oxford Oak Logs RADCO BURNERS FOR VENTED NATURAL GAS LOGS OPERATING APPLIANCE FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: Keep flue open when operating unit. WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electric switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. LIGHTING INSTRUCTIONS 1. STOP! Read the safety information, above. 2. Turn the gas shut-off valve to OFF. 3. Wait five (5) minutes to clear out any gas. If you then smell gas STOP! Follow the safety information above. If you don't smell gas...
Эта инструкция также подходит к моделям:Водонагреватели - CPVSR18 (921.8 kb)