Оценок - 7, средний балл: 3.9
(
)
)
|
Фрагмент инструкции
-When the part is sung with a very low voice containing a lot of harmonics. * If the BR-600 is frequently incorrect when detecting the pitch, either change the “Type” setting for the pitch correction function. In certain cases, this will reduce the number of incorrect detections. Section Rev0.10 123 Fixing the Pitch of Vocals (Pitch Correction) Using the Pitch Correction Fixing the Pitch of Vocals (Pitch Correction) Using the Pitch Correction Let’s now use the BR-600’s pitch correction feature to clean up some mistakes in a solo vocal part. Using this feature, we will be able to correct pitches in real time and in semitone units. 1 Before using pitch correction, record a solo vocal track to work with. 2 Press [REC MODE] several times until the BOUNCE indicator lights up. The BR-600 will now enter Bounce mode. 3 Confirm that [PAD] is not lit, then press [PITCH CORRECTION]. This button will light up to indicate that the Pitch Correction is turned on. The Pitch Correction patch selection screen will appear. 4 Press CURSOR [ ] [ ] to move the cursor to “LOCAT,” and press [ENTER]. 5 Use TIME/VALUE dial to select the track containing the solo vocal recording. The following tracks can be selected at this time: Tracks 1–8, Tracks 1 2– 7 8 6 Start playback on the BR-600. Pitches will be corrected in the solo vocal part as it is played. Listen to the part to confirm that it is now completely in tune, and if necessary, adjust the volume of the part using the corresponding track fader. Press [STOP] to end playback. 7 Press [EXIT] to return to the patch selection screen. 8 Use [CURSOR] to move the cursor to the patch number and select a patch using the TIME/VALUE dial. “Pitch Correction Patch List” (p. 207) 9 Press [EXIT]. 10 Use [CURSOR] and the TIME/VALUE dial to select the track or V-track to which the edited result is to be recorded. The button for the selected track flashes in red, indicating that the track has been selected as the REC track. * The track button alternately lights orange and green when a track or V-track to which material has already been recorded is selected as the recording destination. 11 Move the faders for all tracks except the track containing the solo vocal recording all the way down. Note that this also applies to the Rhythm fader. 12 Press [ZERO] to jump to the start of the song and then press [REC]. [REC] will turn red and start to flash, indicating that the BR-600 is now ready for recording. Rev0.10 124 13 13 Both [PLAY] and [REC] will light up and recording will start. The solo part will be played and any incorrect pitches will be fixed. At the same time, the corrected part will be recorded on the selected track. 14 Press [STOP] at the point where you want to stop recording. The BR-600 will stop playback. 15 Press [ZERO] to jump to the start of the song once again and then start playback of the recorded track. Move the fader for the track containing the original vocal part all the way down, and raise the fader for the track containing the corrected vocal part to an appropriate point. As you listen to the corrected part, confirm whether or not you are happy with the corrections. If you do not like the way the vocal part was corrected, use Undo (p. 64) to cancel the recording. Fixing the Pitch of Vocals (Pitch Correction) 125 Section Rev0.10 Fixing the Pitch of Vocals (Pitch Correction) Setting the Correction Method for Vocal Pitch (Pitch Correction Edit) Fixing the Pitch of Vocals (Pitch Correction) Setting the Correction Method for Vocal Pitch (Pitch Correction Edit) Each of the preset patches 1–5 uses a slightly different method for correcting pitches. Normally, it will be sufficient to select the patch that gives the results you like best; however, if you cannot achieve favorable results using any of these patches, you can change the Pitch Correction settings to create a patch of your own. 1 Select a preset patch to base your new patch on. 2 Press CURSOR [ ] [ ] to move the cursor to “EDIT,” and press [ENTER]. The Pitch Correction edit screen will appear. 3 Use [CURSOR] to move the cursor to the setting you want to change and select a new value using the TIME/VALUE dial. Type LO.MALE, HI.MALE, LO.FEML, HI.FEML Set this parameter to match the type of voice in the original vocal part. If this parameter is not set correctly, problems will be more likely to occur in pitch detection and correction. LO.MALE (Low Male) Select this setting for a low-pitched, male voice. HI.MALE (High Male) Select this setting for a high-pitched, male voice. LO.FEML (Low Female) Select this setting for a low-pitched, female voice. HI.FEML (High Female) Select this setting for a high-pitched, female voice. * If the BR-600 is frequently incorrect when detecting the pitch, either change the type setting. In certain cases, this will reduce the number of incorrect detections. Smooth 0 – 100 This setting determines how quickly pitch correction will react to changes of pitch in the original vocal part. Large values re...
Эта инструкция также подходит к моделям:Музыкальные инструменты - BR-600 (5.26 mb)