NOTE: The date (year, month and day) may not be set by RS-232. In this case, please set at the desired date after setting the date at different year, different month and different day. 6.2.2.4 Request State (Second Category=0x06) PC Request: <0x41>, <0x01>, <0x20>, <0x02>, <0x06>, <0x00>, <0x4f> DVR Response: <0x41>, <0x20>, <0x01>, <0x02>, <0x06>, <0x01>, , <0x4f> Description of : STATE_STOP 0 STATE_REC 1 STATE_PLAY 3 STATE_SETUP 6 STATE_SEARCH 7 STATE_BACKUP 15 STATE_NET_PLAY 23 6.2.2.5 Time Search (Second Category=0x0b) PC Request: <0x41>, <0x01>, <0x20>, <0x02>, <0x0b>, <0x06>, <6 Time Value >, <0x4f> where < 6 Time Value > = year ( 2 bytes, = LowByte + HighByte*256 ), month ( 1 byte), day (1 byte), hour(1 byte),min(1 byte) Example: to search 06/12/2002 17:00 the Time Value = <0xd2>,<0x07><0x06>,<0x0b>,<0x11>,<0x00> where 2003= 210(=0xd3) + 7(=0x07) *256 NOTE: The DVR accepts RS-232 time search commands only under the live or playback Mode. 55 7. Mobile Rack Installation Usually, the unit comes with one hard-disk drive installed in compartment HD 1, which is default-configured as a master. The jumper settings configuration of the installed hard-disk drives for the unit and compatible drives which can be used with this unit are listed in the table below. To install a hard-disk drive in compartment HD 2, please take the following steps. The jumper settings of hard-disk drives for the system Location Jumper IDE 1 Compartment HD 1 Master IDE 2 Compartment HD 2 Master 1. Make sure that the key unlocked. 2. Pull the active-handle outward to remove the carrier body away from the mobile rack 3. Slide the top cover backward and remove. 4. Setting the jumper of your hard-disk drive. The way to set the jumper of the drive varies between manufacturers; please refer to the instructions on the drive to set the jumpers in the master position. 56 5. Attach the interface connector and the power connector to the drive. Please note the red lining of the IDE cable and the red wire of power cable must line up side by side. 6. Place the hard-disk drive inside mobile rack, Use four of the provided screws. 7. Place the top cover back to the carrier body by sliding forward to secure. 8. Slide the carrier body back in the mobile rack. 9. Push the carrier body further into the mobile rack until fully inserted. 57 10. Push the active-handle inward. 11. Lock the Key. 58 8. System Default MAIN MENU RECORD ALARM CLOCK / TIMER COMMUNICATION DISK SYSTEM GOTO REC PAGE REC SETTING REC RATE REC QUALITY DISK FULL AUDIO MULTIPLEXER : 20 F/S : BEST : REWRITE : OFF : ON MAIN PAGE SET REC RATE MAIN MENU RECORD ALARM CLOCK / TIMER COMMUNICATION DISK SYSTEM GOTO ALARM PAGE ALARM SETTING ALM OPERATION : OFF REC RATE REC QUALITY AUDIO ALM TYPE ALM DURATION PRE- ALARM : 20F/S : BEST : OFF : NO : 0 SEC : OFF MAIN PAGE ALARM REC ENABLE MAIN MENU RECORD ALARM CLOCK / TIMER COMMUNICATION DISK SYSTEM GOTO CLOCK / TIMER PAGE CLOCK / TIMER CLOCK : SET REC ENABLE : OFF TIMER : SET MAIN PAGE TIMER REC ENABLE 59 MAIN MENU RECORD ALARM CLOCK / TIMER COMMUNICATION DISK SYSTEM GOTO COMM PAGE SYSTEM MAIN MENU RECORD ALARM CLOCK / TIMER COMMUNICATION DISK SYSTEM OPERATION LOG : ENTER MENU BACKGND : 2 BUZZER : ON PASSWORD : SET SETUP PWD : OFF DEFAULT : LOAD SD SETUP : SAVE VERSION : ENTER MAIN PAGE VIEW OPERATION LOG GOTO SYSTEM SETTING COMM SETTING COMM ID : 01 RS232 : ON RS485 : ON NET ENABLE : OFF NET DHCP : OFF NET IP : SET FTP SETTING MAIN PAGE SET RS232 / RS485 ID MAIN MENU RECORD ALARM CLOCK / TIMER COMMUNICATION DISK SYSTEM GOTO DISK PAGE DISK SETTING REFORMAT HD 2 USAGE BACKUP : HD 1 : REC : FULL 2 MAIN PAGE DISK REFORMAT/CLEAR 60 9. O.S.D Message No. O.S.D Message NO DISK Meanings No hard-disk detected after power activated BATTERY LOW Suggest change the battery and reset the system time LOADING System Boot up VIDEO LOSS Video loss VIDEO IN Video input source KEY LOCKED Key lock function is on KEY UNLOCKED Key lock function is off n1 OF n2 ITEMS PROGRESS n3 % BACKUP n1/n2 NOW n3 % BACKUP COMPLETE Backup complete HD2 SPACE NOT ENOUGH HD2 has not enough space for backup NO RECORD FOR BACKUP BACKUP INCOMPLETE NOT FOUND No backup is possible. Backup incomplete, since the user has pressed the STOP button to stop it The system cannot find a video in the Search function. END DISK FULL EMPTY SET TO NTSC, PLS RESTART Playback of recorded video has reached the end point Hard-disks are full; this happens only when the DISK FULL item in the setup menu is set to STOP. The user presses the PLAY button or uses the SEARCH function, but no video can be played. System has to be set to NTSC, please reboot (PAL is similar) SOFTWARE UPDATE PLEASE RESTART NO DISK DATA NOT CONTINUOUS DISK ATTACHED Software update The system should be rebooted after the software has been updated The user has pressed the Save key without putting in a SD card, or there is a disk error. The system finds data in installed HDs cannot be used contiguously. Suggest y...
)
