Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Once all your devices are connected, you can set up the PowerTouch (see Chapter Two). Refer to the following pages for details on connect ing these devices: Speakers pageE 4 TV pageE 8 VCR(s) pageE 12 CD Player, Kenwood 200-Disc Changer pageE 14 DVD Player pageE 16 MD Recorder pageE 20 Tape Deck(s) pageE 20 Laser Disc Player pageE 24 Turntable pageE 28 Camcorder/Second VCR pageE 29 Antennas pageE 31 All necessary cables should be provided with your home entertainment device (not with new receiver). If you do not have the correct cables, you may purchase these cables from any home entertainment store. To make coaxial digital connections, be sure to use a high-quality digital audio cable, not a standard audio cable. Do not plug in the receiver or any other device to AC power until all connections have been made. Once all devices have been connected, you may plug them in and provide power. Important: Your new receiver requires adequate ventilation to perform reliably. Be sure not to block the ventilation area on the top or back (or both sides) of the receiver with another device. These areas should be: at least top; 50cm, back; 10cm, and left and right side; 10cm Do not install your receiver where direct sunlight or high frequency flourescent lighting can shine directly into the remote sensor. This can cause your new receiver to malfunction. Before You Begin This manual covers the most common and standard connections to the receiver. Because of its versatility, you may decide to connect your devices differently. Before making any video connections to the your receiver : • You can use either S-Video or standard composite (RCA) video connections. • If all of your video devices and TV have S-Video connectors, we suggest that you use them exclusively, since it will provide superior video performance. • If only some of your video devices and TV have S-Video connectors, you can still use them for those devices and the TV. Use the composite 1 connectors for your devices that don’t have S- Video connectors. In this case you’ll also have to connect the receiver’s composite Video Monitor output to your TV for your non S-Video devices and switch between inputs on TV. • If your TV doesn’t have S-Video connectors, you can’t use S-Video connections for any of your video devices. Use the composite connectors exclusively. • If your TV does not have any video connections at all (it only has antenna connections), you must purchase an RF modulator that converts video signals into antenna signals to use it with the KRF-X9992D. You should be able to find an RF modulator at a store specializing in electronic parts. Connections Chapter One : Connecting Your Devices Audio-Video Receiver KRF-X9992D Connections 2 The following diagram shows the entire back of the KRF-X9992D. VIDEO4 6CH.INPUT CENTER SUBWOOFER SURROUND VIDEO 4 INPUT 6 CH 2 CH Chapter One our Devices Audio-Video Receiver KRF-X9992D Noting Your Devices Jack Set Device Manufacturer Model # Setup Code Connections Phono CD1 MD/Tape1 CD2/Tape2 Monitor Video (TV1 on PowerTouch) Video1 3 Video2 Video3 Video4 Use this table and the diagram on the preceding page to plan your connections before you make If your digital cable is... Choose this jack set... You will need this information later, when you set up your PowerTouch (see “Identifying Devices For them, or use it to record your connections as you PowerTouch Control” on pageE 37). Recording this make them. If you will be connecting a DVD player optical VIDEO4 information now will save you additional trips or other device with a digital output, please refer to behind your home entertainment cabinet. You will the following chart before choosing a video jack set: coaxial VIDEO2 or 3 fill in the Setup Code column when you are setting up PowerTouch. ConnectionsConnections Chapter One Devices Audio-Video Receiver KRF-X9992D Connecting Speakers 4 A B C POWERED SUBWOOFER R FRONT L FRONT CENTER R SURROUND L SURROUND VIDEO4 6CH.INPUT CENTER SUBWOOFER SURROUND VIDEO 4 INPUT 6 CH 2 CH Chapter One Devices Do not plug in the receiver to AC power until all connections have been made. To Connect Front Speakers If you only intend to listen to stereo sound opposed to surround sound), you may simply connect a single pair of speakers. To do so: 1. Loosen the speaker wire binding posts. 2. Insert the wire from the positive jack on the RIGHT FRONT speaker into the U-shaped slot in the base of the positive RIGHT FRONT post. Lay the wire to the right of the post; that way, when you tighten the binding post, it will naturally twist the wire into the best connection. Tighten the post. Repeat for the negative wire on the RIGHT FRONT speaker as shown to the right. 3. Repeat step 2 for the positive and negative wires on the LEFT FRONT speaker. Connecting Speakers, continued To Connect Front and Speakers: To listen to the full surround sound receiver can put out, connect front speakers, center, left surround, and right surround speakers. To do so: 1. Loosen...