Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Driver’s Side Under dash mounting provides an easy location for wiring most of the system’s connections, however this is a common location for an intruder to check for an alarm after breaking into the vehicle. SIREN: Mount the siren under the hood to an inner fender-well, wheel-well, or other body surface with the open end facing downward. Run the red siren wire through the firewall using a rubber grommet. Ground the sirens black wire to metal near the siren or you can use one of the siren’s mounting screws for a ground. LED: 2 PIN PLUG Mount the blue LED in a visible location on the dashboard or console. The LED is used as a VALET/PROGRAMMING indicator and it will also FLASH for use as security deterrent when Remotely Locking the door. Valet/Programming Button: 2 PIN PLUG (REQUIRED FOR PROGRAMMING & LEARNING REMOTES) This switch is used for programming features, transmitters, valet mode, and to override the optional starter disable (if installed) in the event of a non-operating remote control. Mount the Valet/Override/Program push- button in a hidden but accessible location. It is REQUIRED for emergency disarm, programming features and entering or exiting Valet Mode. VALET / PROGRAM SWITCH STATUS LED 3 WIRING GREEN WIRE: (-) NEGATIVE DOOR TRIGGER Identify the wire that reads ground when any door is open and 12 volts when all doors are closed. Some vehicles may have isolated door triggers. In this case you may need to run additional wires from other doors or go directly to the wire that triggers the vehicle’s interior dome light. Sometimes newer vehicles contain a separate body control module (BCM) where the door trigger circuit can be located. One vehicle will not require the use of BOTH Negative and Positive door trigger wires. VIOLET WIRE: (+) POSITIVE DOOR TRIGGER Same as the GREEN wire above except this wire is used for vehicles that show a positive voltage (12 volts) when the door is open and a ground when doors are closed as in many Ford, Lincoln, and Mercury vehicles. BLACK WIRE: SYSTEM CHASSIS GROUND The Black wire MUST be connected to the CHASSIS METAL of the vehicle. Scrape away any paint or debris from the connection point and use a star washer to ensure a good connection. Keep the ground wire short. YELLOW WIRE: IGNITION SWITCHED “ON” AND “START” +12 VOLTS Connect to an IGNITION wire (or fuse in the fuse box) that shows +12 Volts when the key is in both “On” and “Start” (WHEN CRANKING) positions. GRAY WIRE: (-) NEGATIVE AUX REMOTE OUTPUT 1 (Optional, may require a relay) Connect to the Negative trunk release circuit or to the activation circuit of an auxiliary module or device. If the circuit requires +12V, then a relay is required. RELAY WIRING: Connect the Gray wire to terminal 85, connect relay terminals 86 and 87 to +12V constant power. Connect terminal 30 of the relay to the +12V positive device/circuit to be activated. BLUE WIRE: (-) NEGATIVE HOOD/TRUNK TRIGGER (Optional) Input trigger for a grounding hood or trunk pin switch. Connect to existing hood and trunk pin switches that read ground when open. If no existing switches are available, install new pin switches if desired. Note: DO NOT mount new pin switches in water pathways. 4 WIRING BLACK/WHITE WIRE: (-) NEGATIVE DOME LIGHT ILLUMINATION OUTPUT (Optional, requires a relay) This wire provides a (-) negative ground when the system is disarmed to activate a vehicles dome light circuit. We recommend the use of a relay for this connection. Connect Black/White to terminal #85 of relay. Connect terminal #86 to fused constant +12V. Connect terminal #87 to a +12V constant or ground source depending on the type of dome light circuit in the vehicle. Connect Terminal #30 to the dome light circuit in the vehicle. BROWN/WHITE WIRE: (-) NEGATIVE HORN PULSE / CHIRP OUTPUT (Optional, may require a relay) Connect to the Negative Horn Trigger wire usually located near the steering column. If the vehicle horn circuit requires +12V, then a relay is required. ORANGE WIRE: (-) NEGATIVE ARMED OUTPUT (500mA Ground, Optional) This wire becomes a constant Ground output when system is armed. This output can be used to activate optional devices such as extra sensors, LED’s, window roll-up modules, voice modules etc. WHITE/RED WIRE: (-) NEGATIVE AUX REMOTE OUTPUT 2 (Optional, may require a relay) This wire connects the same way as Remote Output 1 see GRAY WIRE description above. BLUE/WHITE WIRE: NOT USED BROWN WIRE: (+) SIREN OUTPUT (3 Amp Max.) Connect to RED siren wire from the Siren in the engine compartment. WHITE WIRE: +12V FLASHING PARKING LIGHT OUTPUT Connect to the switched parking light wire at back of light switch. If this is not possible, connect directly to one of the parking lights at the front of the vehicle. European vehicles require separate right and left circuits. Use a dual relay or 2 diodes to separate the output signal. RED WIRE: +12V POWER INPUT (15 amp fuse) Connect to +12 Volt source with supplied fuse & holder. Recommended location for th...