Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
z Please make sure the vehicle is well parked in a safe place. Make sure that the engine and the power are switched off. z Avoid installation outdoors during rain or thunder storms. z The instructions presented in this manual are based on the passenger seat at the right of the driver’s seat. In an opposite situation, change the directions accordingly. z Objects on the monitor are closer than they appear. • This I/R camera is not a safety device. Safe driving is the driver’s responsibility in all circumstances. NOTICE-DISCLAIMER Under no circumstances shall the manufacturer or distributor of the I/R CAMERA be held liable for consequential or incidental damages sustained in connection with the use of the I/R Cam rear vision system. The I/R Camera is designed as a safety enhancement device and is in no way intended as a replacement for rear-view mirrors, side-view mirrors or physically checking the surroundings when backing a vehicle. Always check surroundings for safety when backing. Objects on the monitor are closer than they appear. For the best fit, modification of the vehicle license may or may not be necessary. It is the sole responsibility of the vehicle owner to check and verify any and all state or federal motor vehicle codes with regard to modifications of vehicle license plates. 1770 SOUTH TAPO STREET • SIMI VALLEY, CALIFORNIA 93063 800-998-6880 • 805-526-9400 • FAX 805-581-9500 WWW.CRIMESTOPPER.COM Page 1of6 Compilation and Publication Notice Under the supervision of PEC, this manual has been compiled and published, covering the latest description and specification. The contents of this manual and the specifications of this product are subject to change without notice. PEC reserves the right to make changes without notice in the specification and material contained herein and shall not be responsible for any damages (including consequential) caused by reliance on the materials presented, including but not limited to typographical and other errors relating to the publication. PACKAGE CONTENTS Check your package for the listed contents. If you do not find all of the listed items, contact the supplier from whom you purchased the camera before installing the unit and accessories. (1) I/R Camera (1) Mounting Bracket (4) Screws (1) Screw Wrench (1) 20 Ft. (6 Meter) Cable 1770 SOUTH TAPO STREET • SIMI VALLEY, CALIFORNIA 93063 800-998-6880 • 805-526-9400 • FAX 805-581-9500 WWW.CRIMESTOPPER.COM Page 2of6 INSTALLATION Step 1: Testing the Camera (Bench Testing) 1. Prepare two sets of DC 11-13V batteries for running a bench test to make sure the camera functions are working properly (before you actually install the camera into your vehicle). 2. Refer to the wiring diagram (4.1-3) the camera and the monitor each have to have their own power source, DO NOT connect with the same battery. 3. When connecting the 20’ cable, make sure all connectors have been solidly connected. 4. Turn on the monitor and you should see a clear, color picture display. 5. If you do not see a picture or the picture quality is not satisfactory, please turn off the monitor and double check all the connectors to make sure they are securely connected. 6. Turn on the monitor again. If you are still unable to see the picture or the picture quality has not improved, contact your supplier for assistance. Step 2: Checking the Power Source 1. The camera can only operate by connecting a power source of DC 1113V+ / 70mA type. 2. Check your vehicle and make sure you have the correct power source for the camera. 3. In most cases, the camera power line is connected with the reverse light power source. 1770 SOUTH TAPO STREET • SIMI VALLEY, CALIFORNIA 93063 800-998-6880 • 805-526-9400 • FAX 805-581-9500 WWW.CRIMESTOPPER.COM Page 3of6 Step 3: Camera Installation 1. Determine the proper location on your vehicle to install the camera. 2. Make sure the area surface is clear, clean and flat. 3. Install the mounting bracket. (Refer to Diagram 3.1-1) 4. Assemble the camera inside of the mounting bracket (Refer to Diagram 3.1-2) 5. Adjust the viewing direction and angles to attain the best viewing (Refer to Diagram 3.1-3) Diagram 3.1-1 Diagram 3.1-2 Diagram 3.1-3 . Step 4: Wire Connection 1. Connect the power source line to the camera. Also connect 20’ cable to the monitor. (Refer to Diagram 4.1) 4 pin connector 2 1 4 3 RED Power Input 12V(+) BLACK Power Input 12(-) Waterproof Camera Connector Video Output Standard Cable Connector Diagram 4.1-1 Pin No. PART-DESC 1 Video Output 2 Power DC 12V 3 GND 4 Diagram 4.1-2 1770 SOUTH TAPO STREET • SIMI VALLEY, CALIFORNIA 93063 800-998-6880 • 805-526-9400 • FAX 805-581-9500 WWW.CRIMESTOPPER.COM Page 4of6 Video output to monitor 1770 SOUTH TAPO STREET .SIMI VALLEY, CALIFORNIA 93063 800-998-6880 .805-526-9400 .FAX 805-581-9500 WWW.CRIMESTOPPER.COM Diagram 4.1-3 2. In most cases and as a time saver, connect the camera power wire at the rear of vehicle behind the reverse lights. The red power wire line goes to the reverse lig...